how to cut popsicle sticks

How to Cut Popsicle Sticks.

If you’re having some fun by engaging in some arts and crafts, you may need to cut some popsicle sticks. Cutting popsicle sticks can be tough, since the flimsy wood has a tendency to slide out of regular scissors and splinter when you cut it. To cut popsicle sticks while minimizing the chance of splinters, use serrated scissors if you don’t mind a rough edge. For a smoother edge, use wire cutters or snips depending on what is available to you.





Splitting with Serrated Scissors.



Grab a pair of heavy-duty kitchen or craft scissors. Standard scissors with a flat blade won’t easily cut through a popsicle stick. However, you can use any pair of serrated scissors that are designed for the kitchen. Large pairs of craft scissors will work as well.

This method will leave a rough edge behind wherever you cut.



Open your scissors and hold the popsicle stick against the blades. Put your thumb and index finger in the finger holes. Hold the popsicle stick that you want to cut in your nondominant hand. With your blades opened all the way, place the section that you want to cut as close to your handle as possible so that it sits perpendicular at the junction where the 2 blades meet.

You’ll need special scissors if you’re left-handed.

Warning: Keep your fingers at a safe distance away from the blades.





Close the finger holes quickly and firmly to cut the stick. With your other fingers at a safe distance, bring your thumb and index finger together to start closing the blades. Close your scissor blades all the way through the popsicle stick until the two blades snap together. The harder you close your scissors, the less likely you are to fray the edge.



Inspect your edge and remove any splinters. You don’t want random pieces of wood falling off of your popsicle stick. After you’ve cut it, hold it up to your eye and look for splinters. If there are any, carefully pinch them between your thumb and index finger and pull them off.

You can use sandpaper to smooth out rough edges by gently rubbing it on the edge where you cut your popsicle stick. Any grit sandpaper will work.







Using a Wire Cutter.



Find a pair of wire cutters with a flat blade bigger than 1 inch (2.5 cm). You are only going to use the wire cutters to brace the popsicle stick in place when you snap it, so the blades don’t have to be sharp. Wire cutters create a lot of even pressure between their blades when you close the handles. This means that they are unlikely to cause a splinter or uneven edge where you snap the popsicle stick.

You can use a pencil to draw a guide line where you want to cut the popsicle stick. This will help you keep your wire cutters positioned correctly when you twist your wrist to make your cut.



Hold your wire cutters loosely while you line them up on the stick. Wrap your dominant thumb over the top handle of the wire cutters and put your other fingers around the bottom handle. Hold your hands steady and put the popsicle stick in the wire cutter’s jaws. Slide your popsicle stick in the tool’s jaws to find the spot that you want to cut it.



Tighten your grip and hold the popsicle stick in place. You don’t need to squeeze very hard to get the blades to tighten around your popsicle stick. Don’t push down hard, or you’ll risk snapping the stick.

Even though they tend to have smaller blades than scissors or snips, wire cutters pack a punch when you squeeze the handles. Keep your free hand clear of the blades while you position your popsicle stick.



Wiggle your wire cutters back and forth while keeping them closed. With your free hand, hold the longest section of your popsicle stick in place by wrapping your fingers around it and staying still. Then, move your wire cutters back and forth in order to loosen the wood at the junction where you’re holding them.

Keep your grip at the same level of pressure while you move your wire cutters.



Snap the wood off by twisting the wire cutters. Once you hear a few creaks from the wood loosening, you can snap the stick by rotating the wire cutters with your wrist. Turn your wrist sharply to the left and right without moving your arm. The popsicle stick will snap at the junction where you held it with the wire cutters.

Tip: Don’t pull away or move your arm while you do this or you’ll risk leaving a jagged edge.





Cutting with Snips.



Choose your snips based on how you want to cut. Snips are color coded based on the direction that they’re designed to cut. Green snips make cuts to the right, red snips make cuts to the left, and yellow snips cut straight lines. Choose your snips based on whether you’re trying to cut at an angle or make a straight cut.

The advantage of using snips is that they’re going to cut quickly. They may make your popsicle stick slide as you cut it though, so keep a firm grip while cutting.



Open your grip and position your cut. Hold the popsicle stick in your nondominant hand and loosen your grip on the snips to open the blades. Position your popsicle stick between the blades wherever you want to cut it and hold it steady.

Keep your free hand clear from the blades as you position your stick.



Squeeze the handles to close the blades and make your cut. You don’t need to squeeze hard; snips are designed to cut sheet metal and generate a lot of cutting power automatically. As you squeeze, keep the popsicle stick still so that your cut stays consistent. Tighten your grip until you hear a snap and then release the handles.

Tip: Remove any splinters by pinching them between your thumb and forefinger and pulling them off.





Tips.

You can use sandpaper to smooth out jagged edges after you cut them. All you have to do is hold a small piece of sandpaper in your dominant hand and lightly drag it back and forth across the edge where you cut your stick.

Popsicle sticks tend to splinter no matter how you cut them, but they’re also are relatively cheap. Buy a few extra bundles so that you always have some extra sticks laying around in the event that you split a few them.

Warnings.

Never use snips, scissors, or wire cutters without the supervision of an adult. If you need help, your parent or teacher will be able to cut your popsicle sticks for you.

Always keep your free hand away from the area that you’re going to cut.

Work at a stable table with plenty of room.

November 10, 2019

how to easy build a ballista

How to Build a Ballista.

If you like medieval weaponry capable of flinging arrows through the air, try building your own ballista. A ballista consists of a frame, a launch ramp with a slide, and a tensioned string. You can build all of these components with popsicle sticks, thread, and other basic supplies. Add a launch pin to create a small ballista that enables you fire bolts with a pull of a string.







Part 1 Assembling the Frame.



Drill holes through a pair of 6 in (15 cm)-long popsicle sticks. Measure 1 in (2.5 cm) from the ends and mark the spots with a pencil. Before working on the sticks, lay down a piece of cardboard to protect your work surface from damage. Then, use a drill bit 1⁄4 in (0.64 cm) in diameter to create the holes.

The simplest way to create a ballista is with inexpensive popsicle sticks, available online, at craft supply store, and other areas.

If you wish to make a larger ballista, trying using larger pieces of wood or foam in place of the popsicle sticks.



Poke a second, smaller hole next to each of the bigger ones. Measure about 1⁄4 in (0.64 cm) along the stick’s length from one of the existing holes. Use a steel probe 1⁄16 in (0.16 cm) in diameter or a similar sharp tool to poke all the way through the wood. Position the hole so it’s slightly lower, closer to the edge of the stick, than the larger hole. Create a matching hole on the opposite end of the first stick and create corresponding holes on the second stick.

Each popsicle stick has 4 holes when you’re finished, a pair of holes on either end. The bigger holes are used to secure the ballista frame together, while the smaller holes are for the launcher.

To test the smaller holes, try squeezing a wood cocktail skewer through them. Get skewers about 7⁄64 in (0.28 cm) in diameter. Widen the holes as needed to fit the skewers.



Cut a pair of wood blocks to 1 1⁄2 in × 1 in (3.8 cm × 2.5 cm). The easiest way to do this is to purchase wood crafting blocks. If you can’t find the exact size you need, cut the blocks to size with a crafting knife or another tool. Get blocks that are about 1 in (2.5 cm) tall. Scrape away the excess wood until both blocks are the same size.

Shop online or visit a craft store to see what kind of wood blocks are available. You can use scrap wood if you wish, but crafting blocks are much smoother and easier to work with.

Be careful when using a crafting knife. The blocks are small, so it’s easy to slip while handling the blade. Work slowly to avoid potential accidents.

Image titled Build a Ballista Step 4

4

Glue the blocks to the ends of the popsicle sticks. Heat up a hot glue gun loaded with a fresh stick of white glue. Spread a layer of glue over the ends of the 1 of the sticks, then lay the blocks on top of that. Align the longer ends of each block with the edges of the popsicle stick. Spread another layer of glue on top of the wood blocks to secure the second popsicle stick.

Make sure you align the holes in the popsicle sticks before gluing them in place. The holes need to be positioned evenly over one another in order for the ballista launch its arrows later.







Part 2 Building and Attaching the Launch Ramp.



Cut about 1⁄2 in (1.3 cm) off the end of another popsicle stick. Trim this new stick to size by measuring and slicing it apart with your craft knife. Another safe way to do this is by snapping the end off with scissors or wire cutters. Trim any stray wood fibers off the cut end so it looks smooth and even.

Cutting popsicle sticks can be tricky since they are pretty fragile. Work slowly, gradually deepening the cut you make. Bend the popsicle stick back and forth along the groove you cut to prevent it from splintering.

If you have experience with wood cutting, try using a fine saw blade like a band saw. Always wear earmuffs, eye goggles, and a dust mask while operating a saw.



Trim a pair of cocktail skewers to 5 1⁄2 in (14 cm) in length. Get some wood skewers about 7⁄64 in (0.28 cm) in diameter. Measure and mark the skewers as needed with a ruler and pencil. Then, cut the skewers evenly on both ends to trim off the sharp points. The skewers need to be the same length as the popsicle stick you cut, so use it for comparison.

Wood skewers are available online in addition to some craft stores, general stores, and restaurant supply stores.

Cut the skewers by using a craft knife or by snapping the ends off with wire cutters.



Glue the skewers to the top of the popsicle stick. Place the skewers on the long edges of the popsicle stick you cut. Lay down a bead of glue from a hot glue gun to secure the skewers in place. Trim the ends of the skewers as needed to smooth them out and make them even with the ends of the stick.

Now you have a basic launch ramp. The skewers form a groove for you to load the ballista’s ammunition.



Secure the ramp to the center of the frame you built. Get your popsicle stick frame with the holes drilled in it. Turn the ramp over and spread some hot glue on the end of it. Then, secure it over the bottom popsicle stick in the frame. Put it as close to the center of the frame as possible, aligning the end of the ramp with the back edge of the frame.

Hot glue dries relatively quickly, so you don’t need to worry too much about the frame and ramp components coming apart. Set the pieces aside as needed for 10 to 20 minutes to give the glue a chance to solidify. It takes about 24 hours to fully cure.







Part 3 Creating the Launcher Mechanism.



Break a 4 1⁄2 in (11 cm) popsicle stick into halves. Divide the stick evenly into halves about 2 1⁄4 in (5.7 cm) long. These sticks are smaller than the frame pieces and are part of the ballista’s launching system. Use a craft knife or wire cutters to split the stick across its width and then smooth out the cut end.

Purchase a separate bag of smaller popsicle sticks online or at a craft store. Alternatively, cut smaller pieces of wood boards or foam if you’re making the ballista with those materials.



Poke a hole 1⁄2 in (1.3 cm) from the end of each stick. Use a 1⁄16 in (0.16 cm)-thick steel probe or a similar tool sold at craft stores. Make a single hole near the rounded end, leaving the cut end alone. Pierce all the way through the wood.



Pull pieces of string through the larger holes in the frame. Getting the string through the holes is tricky, so have a cocktail skewer nearby to push it through. Slide both ends of a string 7⁄64 in (0.28 cm) in diameter through the top hole, then through the respective hole in the bottom frame piece. Leave the string long enough to form small loops above and below the ballista frame.

Try using twine from a craft store for a strong material that isn’t likely to break when you’re having fun launching makeshift arrows.



Tie small skewers to the frame using the string loops. Cut a couple of wood skewers down to 1 1⁄2 in (3.8 cm) in length. Start with the top loop by placing a skewer inside of it and pulling the string tight. Then, tie the loose ends of the string into a knot with another skewer underneath it.

Lay the skewers flat against the frame pieces. Orient them so they’re perpendicular to the frame pieces. Then, tie the knots as tight as you can to hold the skewers in place.



Place the small popsicle sticks between the strings and tighten them. The popsicle sticks you cut earlier fit between the frame pieces. Slide about 1⁄2 in (1.3 cm) of the cut ends of the sticks between the ropes. Then, twist the bottom skewers clockwise to tighten the string as much as possible.

When the small sticks are positioned correctly, you can move them back and forth without them sliding out of place. This is necessary for moving the ballista’s launcher to let arrows fly a long way.



Slide another skewer into each of the inner holes on the frame. Cut 2 more skewers to 1 1⁄2 in (3.8 cm) in length to fit those holes. Make them look nice and even like the other skewers before fitting them through the frame. Make sure the skewers go all the way through the respective holes on the top and bottom frame pieces.

Protect the strings by tying the ends to the bottoms of these skewers, if possible. If you do this, the skewers maintain the string’s tension, leading to much more impressive launches!



Tie a length of string between the launcher’s stick arms. Set the ballista so the back end is in front of you. Thread the 7⁄64 in (0.28 cm)-thick string into the holes in the small popsicle sticks hanging from the ballista frame. Knot both ends of the string to secure it, then trim off the excess length.

The exact length of string you need to form the launcher depends on the material you used. Try threading the string through both holes before cutting it from the spool. Always cut it longer than you need so you can knot it tightly.







Part 4 Making the Slide and Supports.



Glue a block underneath the back end of the launch ramp. Get another 1.5 in × 1 in (3.8 cm × 2.5 cm) wood block. The block needs to be approximately the same width as the ramp in order to keep the ballista stable while you’re firing it. Set the ramp in the glue, aligning its back edge with the back end of the block.

Installing the block makes the ballista ramp slanted so it launches arrows higher into the air.



Cut grooves in a small block to create the ballista’s slider. Cut the grooves into a small piece of wood about 1.5 × 1 × 1⁄2 in (3.8 × 2.5 × 1.3 cm) in size. The launcher needs separate grooves in the front and back, both as thick as the string you used when tying the launcher arms together. Make the 2 grooves about 1⁄4 in (0.64 cm) from either end. Use a crafting knife to scrape away the wood, making the grooves circular and about half as deep as the block.

Try making the slider out of a wood peg bought online or a craft store. If you use scrap wood, make sure it is solid and smooth so you can slide it along the ramp.



Create a 1 1⁄2 in (3.8 cm) wood cap to fit on top of the slider. Simply cut a smaller popsicle stick to the exact length and width as the slider. Cut the cap into a rectangle with no rounded edges. When you’re ready to install it, put the launcher string into the slider’s front groove. Spread some hot glue, then press the cap onto the top of the slider.

Test the cap out by putting it on the slider before you add the glue. Check that it’s big enough to cover the slider and pin the string in place.



Drill 45-degree angle holes in a block of wood. This block needs to be about 2 × 1 1⁄2 × 1⁄2 in (5.1 × 3.8 × 1.3 cm) longer than the one on the back end of the ballista. Position the holes about 1 in (2.5 cm) from the smaller sides of the block. Use a drill bit approximately 1⁄4 in (0.64 cm) wide to drill diagonally towards the center of the block.

Drill all the way through the other side of the block. Keep the holes as even as possible to build a stable base for the ballista frame.



Fit wood dowels into the holes on the block. Use a pair of 1⁄4 in (0.64 cm)-thick dowels cut to about 4 in (10 cm) long. Slice them using a craft knife, wire cutters, or a saw if you have one. Then, put some hot glue on the ends of the dowels and push them as far into the holes as possible.

Look online or at a local craft supply store for the perfect dowels for your project.



Glue the block to the front side of the frame to stand the ballista up. Flip the block over and spread a thick bead of glue across its length. Lift up the front end of the ballista to stick the block to the bottom of the frame. After pressing the pieces firmly together, consider letting the glue dry for about 10 minutes.

If the block is wider than the frame, you could try whittling it down with a carving knife or craft knife. As long as your base is stable, doing this isn’t necessary, but it can make the ballista look a little neater.







Part 5 Completing the Firing Mechanism.



Glue long spacer pieces to the sides of the back block. Cut the spacer pieces so they are about 4 in × 1.5 in (10.2 cm × 3.8 cm) in size. Spread more hot glue, then press them against the block supporting the back end of the ramp. These parts are there to support the rest of the parts you need to add, so they don’t need to be pretty and can be longer than the block itself.

Make sure the spacer pieces stick out from underneath the ramp a little bit. The pieces that attach to them need to extend over the ramp or else you won’t be able to fire the ballista.



Cut 1 1⁄2 in (3.8 cm) off the ends of a large popsicle stick. Measure and mark the length you need to cut on one of the 6 in (15 cm)-long popsicle sticks. You need 2 of these pieces, so cut off both ends of the stick. Leave the rounded ends of the stick intact.

Cut the stick carefully with a craft knife, wire cutters, or saw. Work slowly to avoid splintering the wood and smooth out the edges as needed.



Make a hole about 1⁄2 in (1.3 cm) from the end of each piece. Create the holes by poking a 1⁄16 in (0.16 cm) steel probe or a similar sharp tool through the wood. Keep the holes along the center part of the wood. Make them as even as possible to ensure the ballista parts line up appropriately when you install them.



Glue the popsicle ends to the side pieces on the block. The sticks need to be near the tail end of the block. Also, position the sticks about 1⁄4 in (0.64 cm) up from the bottom edge of the block. Spread glue over the wood and press them onto the block to hold them in place.

Make sure the ends of the sticks extend over the ramp. The holes need to be about level with the top edge of the slider in order to string the launch rope through it.



Bend a metal rod to fit through the holes in the wood. Get a metal rod about 4 in (10 cm) long and about 1⁄16 in (0.16 cm) in width to fit through the holes. Pull the launcher piece back and thread the rod through its second groove and the holes in the sticks. Then, use pliers to bend one end of the rod back over itself. The rod forms a launch pin that stays in place until you're ready to use it.

Test the pin by attempting to move it. If it feels loose, bend the end back on itself more to keep the pin in place. Leave the other end of the pin alone so it can slide out of the hole.



Tie a string to the end of the launch pin. Cut some 7⁄64 in (0.28 cm)-thick string to complete the launching mechanism. Try trimming it to about 3 to 4 in (7.6 to 10.2 cm) in length. Knot the string a few times to the bent end of the launch pin to quickly pull it out when you wish to fire the ballista.

Keep the string at a comfortable length. If it is too long or short, you may have a hard time pulling out the pin in a quick, fluid motion.



Cut cocktail skewers to about 5 in (13 cm) for ammunition. Trim the pointed ends off of as many skewers as you wish to use. When you’re ready to use the ballista, put a single arrow on the chute after pulling the slide back. Yank the string to pull the metal pin out, causing the slide to spring forward, sending the arrow through the air.

Always cut the points off of the skewers to avoid accidents. Also, never shoot the arrows at others. They can hurt, especially from bigger launchers.







Tips.

Ballista arrows are reusable. Collect the arrows after you fire them to ensure you have a steady supply of ammunition.

Small ballista designs can be blown up to create big rigs capable of throwing arrows long distances. Many big ballistas use wood planks and thick rope like the kind available at hardware stores.



Warnings.

Firing a ballista can be dangerous. To be safe, clear an area outdoors and fire it when no one else is around.

If you choose to use a saw to cut components, follow proper safety procedures to avoid injuries. Always wear earmuffs, goggles, and a dust mask.



Things You’ll Need.

Ruler, Craft knife, Wire cutters or scissors.

6 in (15 cm)-long popsicle sticks, 4 1⁄2 in (11 cm) popsicle sticks.

1 1⁄2 in × 1 in (3.8 cm × 2.5 cm) wood blocks, 7⁄64 in (0.28 cm)-diameter wood skewers, 1⁄4 in (0.64 cm)-diameter wood dowels.

1⁄4 in (0.64 cm) drill bit, Drill.

1⁄16 in (0.16 cm) steel probe, Hot glue stick, Hot glue gun.

7⁄64 in (0.28 cm)-thick string, 1⁄16 in (0.16 cm)-diameter metal rod.

November 20, 2019

how to make a paper peacock fan

How to Make a Paper Peacock Fan.

Have you ever made a paper fan? Simple, wasn't it? Have you ever wondered how to make a plain paper fan look more creative and eye-catching? Well, you're in luck, because this article will teach you how to make a paper fan that looks just like a real peacock!

Steps.

1. Gather your supplies.

2. Take your sheet of dark green paper and make one fold up, about two centimetres wide.

3. Turn the paper over to the other side, and make another fold in the same way.

4. Continue turning the paper over and making folds until you reach the end of the paper. You should have an accordion-like pleat of folds.

5. Cut the paper in half along one of the folds. Fold one half of the paper in half, along the width. Repeat with the other half.

Take the inner ends of one half of the paper, and glue them together. Do the same with the other half. You should have two pleated semicircles.

6. Staple the semicircles together to make one full circle. Now you have made a circular fan.

7. Paint small red, yellow and blue dots on your circular fan. Wait for the paint to dry.

8. Glue the sequins on top of the dots of paint for some added sparkle.

9. Cut out a peacock body shape from the blue cardstock.

10. Paint the peacock's body all over with the blue glitter glue. Wait for it to dry.

11. Glue the googly eye onto the peacock's body.

12. Cut out a small triangle from the yellow cardstock, and glue it onto the peacock's body. This is the peacock's beak.

Glue the green feathers onto the peacock's body. These are its wings.

Glue the popsicle stick between a fold on the circular fan.

Glue the peacock's body onto the popsicle stick.

Things You'll Need.

One square sheet of dark green paper.

One A4 sheet of dark blue cardstock.

One small sheet of yellow cardstock.

Dark blue glitter glue.

Red, yellow and blue paint.

Red, yellow and blue sequins.

Three green feathers.

One googly eye.

One popsicle stick.

Desember 18, 2019

how to make a paper peacock fan

How to Make a Paper Peacock Fan,

Have you ever made a paper fan? Simple, wasn't it? Have you ever wondered how to make a plain paper fan look more creative and eye-catching? Well, you're in luck, because this article will teach you how to make a paper fan that looks just like a real peacock!

Steps.

1. Gather your supplies.

2. Take your sheet of dark green paper and make one fold up, about two centimetres wide.

3. Turn the paper over to the other side, and make another fold in the same way.

4. Continue turning the paper over and making folds until you reach the end of the paper. You should have an accordion-like pleat of folds.

5. Cut the paper in half along one of the folds. Fold one half of the paper in half, along the width. Repeat with the other half.

Take the inner ends of one half of the paper, and glue them together. Do the same with the other half. You should have two pleated semicircles.

6. Staple the semicircles together to make one full circle. Now you have made a circular fan.

7. Paint small red, yellow and blue dots on your circular fan. Wait for the paint to dry.

8. Glue the sequins on top of the dots of paint for some added sparkle.

9. Cut out a peacock body shape from the blue cardstock.

10. Paint the peacock's body all over with the blue glitter glue. Wait for it to dry.

11. Glue the googly eye onto the peacock's body.

12. Cut out a small triangle from the yellow cardstock, and glue it onto the peacock's body. This is the peacock's beak.

Glue the green feathers onto the peacock's body. These are its wings.

Glue the popsicle stick between a fold on the circular fan.

Glue the peacock's body onto the popsicle stick.


Question : Instead of googly eyes, can I use a sketch pen?
Answer : Sure! It is always good to experiment with different materials and branch out.

Things You'll Need,

One square sheet of dark green paper.

One A4 sheet of dark blue cardstock.

One small sheet of yellow cardstock.

Dark blue glitter glue.

Red, yellow and blue paint.

Red, yellow and blue sequins.

Three green feathers.

One googly eye.

One popsicle stick.

Januari 23, 2020

how to make a paper bag turkey

How to Make a Paper Bag Turkey.

Looking for a fun way to celebrate this holiday season? Whether you’re crafting homemade decorations for Thanksgiving dinner or just want to get into the spirit of autumn, making a turkey from ordinary paper bags is a quick, simple and creative activity that is sure to please children and adults alike. This project only requires a few simple materials and will add a bit of thrifty Fall flair wherever it’s displayed.

Part 1 Making the Turkey.

1. Gather your materials. For this project, you’ll need only need a handful of basic items—3 brown paper bags (1 large paper grocery bag and 2 smaller standard paper bags), 1 sheet of white 8 ½” x 11” typing paper, a few sheets of newspaper, a pair of scissors and a hot glue gun or some craft glue. Any additional materials will be up to you, depending on how elaborate you want the presentation of your finished turkey to be.

Your turkey will be made of just three easy pieces: one big bag for the body, and the two smaller bags to serve as the “drumsticks.”

Making a paper bag turkey only takes a few minutes from start to finish, leaving you with plenty of time in your day to finish playing, decorating or tackling other crafting projects.

2. Form the body of the turkey. Take the large paper bag and fill it ¾ full with crumpled newspaper. This will help fill out the body, giving it a plump appearance and preventing it from collapsing once it's ready to be displayed. After the bag has been stuffed, fold the corners down diagonally and glue them in place. Tuck the folded tab down one more time and glue it to the underside of the turkey.

Shape the body of the turkey by hand until it’s smooth and round. Be sure to work out any square edges of creases from the original bag.

Be careful not to tear the bag while sealing or shaping it.

3. Shape the drumsticks. Grab the two smaller paper bags—you’ll be using these to craft the “drumsticks” of the turkey. Make one hand into a fist and stick it into each bag, molding the opening of the bag around your wrist. This will give the bag its recognizable drumstick shape. Remove your hand from the bag and fill the rounded end with newspaper. Twist the opening of each bag shut and secure it with a dab of glue.

Like the body of the turkey, the drumsticks will need to be filled in order to hold their shape.

4. Cut the booties for the drumsticks. Your drumsticks aren’t complete until they’re dressed with a pair of frilly white booties, like a traditional Thanksgiving turkey. Cut your sheet of typing paper in half lengthwise, then fold each piece in half, again lengthwise. Use your scissors to make a series of cuts in the open edge of the paper to create a neat fringe.

Try to make your cuts about ¼ inch apart.

Your cuts only need to be about half the width of the paper.

5. Put it all together. Wrap a paper bootie around the end of each drumstick and secure them with glue. Then, place the drumsticks on either side of the sealed end of the turkey and glue them down. That’s it! The result is a quirky, lifelike baked bird that you might just mistake for the real thing.

Attach the drumsticks to the tapered sides of the body where you folded down the edges of the big bag. This will give the turkey a more realistic look.

The different parts of the turkey will have a little weight to them once they’ve been filled. Use enough glue to make sure that everything holds.

Part 2 Finding Creative Ways to Present Your Turkey.

1. Put it on a platter. Arrange your paper bag turkey on a serving platter over a bed of parsley or tissue paper garnish. Surround the turkey with fallen leaves for a splash of vibrant color. With the right details, you’ll have a mouthwatering craft turkey worthy of a fantasy feast to show off to your friends and family.

If you don't have a real serving platter lying around, make your own out of cardboard, construction paper, and colored markers.

Make sure to let everyone, especially small children, know that your paper turkey is not for eating.

2. Add colorful designs. Before you fill the paper bags, decorate the outsides for a more artistic, funky finish. Use crayons, markers, washable paint, stickers or glitter and customize your turkey with polka dots, swirls or dazzling patterns using your favorite colors. Grab a friend, sibling, parent or child to decorate your turkey with, then compare and display them together when you’re done.

If you’re using paint or a felt-tip marker that might saturate the paper bags, allow them to dry before stuffing or shaping them.

When making paper turkeys with your kids or students, have them write down one thing they’re thankful for somewhere on the big bag.

3. Fill it with “stuffing.” For an unexpected tasty twist, ditch the newspaper and fill your turkey with popcorn, candy or other easy-to-eat finger foods instead. You can then have someone “carve” the turkey by cutting a flap in the top and have something to snack on until the main course is served. This imaginative serving style is sure to be a hit at holiday parties!

Popcorn makes a simple stuffing because it’s light and takes up a lot of space, but you could use just about any snack food, like chips, pretzels or chocolates, to fill your turkey.

Try filling the drumsticks separately with caramel corn to make “dark meat.”[6]

4. Put your paper bag turkey on display. In addition to being a fun and easy project to do with your friends or loved ones, your paper turkey will make a unique arrangement for the coffee table, arts and crafts desk or kitchen counter. It will look especially good surrounded by other festive Fall decorations. Best of all, you can store the playful papercraft away or simply make a new one the next time the holiday season rolls around.

A paper bag turkey will fit nicely with other homemade holiday decorations, such as hand turkey cutouts, popsicle stick snowflakes, and construction paper pumpkins.

Tips.

This will make a great activity for parents and teachers to do alongside their children or students.

If the paper bags you’re using have any logos, writings or markings on them, carefully turn them inside out before you begin crafting.

Line the inside of your turkey with wax or parchment paper to prevent splotchy grease stains if you plan on filling it with buttered popcorn.

Make sure you have enough of whatever food item you choose to fill the large bag.

Hot glue is preferable to other adhesives because it dries quickly and creates a strong, lasting hold.

Warnings.

Take caution when working with the hot glue and scissors. Kids should ask an adult for help with the cutting and gluing portions of the project.

Staples should be avoided, as there's no way to use them to secure the different parts of the turkey without mashing them.

Things You'll Need.

3 brown paper bags (1 large and 2 small), 1 sheet white typing paper, A few sheets of crumpled newspaper.

Scissors, Hot glue or craft glue, Popcorn or other small snack foods (optional), Various decorating supplies (optional).

Desember 14, 2019

how to make a paper bag turkey

How to Make a Paper Bag Turkey.

Looking for a fun way to celebrate this holiday season? Whether you’re crafting homemade decorations for Thanksgiving dinner or just want to get into the spirit of autumn, making a turkey from ordinary paper bags is a quick, simple and creative activity that is sure to please children and adults alike. This project only requires a few simple materials and will add a bit of thrifty Fall flair wherever it’s displayed.

Part 1 Making the Turkey.

1. Gather your materials. For this project, you’ll need only need a handful of basic items—3 brown paper bags (1 large paper grocery bag and 2 smaller standard paper bags), 1 sheet of white 8 ½” x 11” typing paper, a few sheets of newspaper, a pair of scissors and a hot glue gun or some craft glue. Any additional materials will be up to you, depending on how elaborate you want the presentation of your finished turkey to be.

Your turkey will be made of just three easy pieces: one big bag for the body, and the two smaller bags to serve as the “drumsticks.”

Making a paper bag turkey only takes a few minutes from start to finish, leaving you with plenty of time in your day to finish playing, decorating or tackling other crafting projects.

2. Form the body of the turkey. Take the large paper bag and fill it ¾ full with crumpled newspaper. This will help fill out the body, giving it a plump appearance and preventing it from collapsing once it's ready to be displayed. After the bag has been stuffed, fold the corners down diagonally and glue them in place. Tuck the folded tab down one more time and glue it to the underside of the turkey.

Shape the body of the turkey by hand until it’s smooth and round. Be sure to work out any square edges of creases from the original bag.

Be careful not to tear the bag while sealing or shaping it.

3. Shape the drumsticks. Grab the two smaller paper bags—you’ll be using these to craft the “drumsticks” of the turkey. Make one hand into a fist and stick it into each bag, molding the opening of the bag around your wrist. This will give the bag its recognizable drumstick shape. Remove your hand from the bag and fill the rounded end with newspaper. Twist the opening of each bag shut and secure it with a dab of glue.

Like the body of the turkey, the drumsticks will need to be filled in order to hold their shape.

4. Cut the booties for the drumsticks. Your drumsticks aren’t complete until they’re dressed with a pair of frilly white booties, like a traditional Thanksgiving turkey. Cut your sheet of typing paper in half lengthwise, then fold each piece in half, again lengthwise. Use your scissors to make a series of cuts in the open edge of the paper to create a neat fringe.

Try to make your cuts about ¼ inch apart.

Your cuts only need to be about half the width of the paper.

5. Put it all together. Wrap a paper bootie around the end of each drumstick and secure them with glue. Then, place the drumsticks on either side of the sealed end of the turkey and glue them down. That’s it! The result is a quirky, lifelike baked bird that you might just mistake for the real thing.

Attach the drumsticks to the tapered sides of the body where you folded down the edges of the big bag. This will give the turkey a more realistic look.

The different parts of the turkey will have a little weight to them once they’ve been filled. Use enough glue to make sure that everything holds.

Part 2 Finding Creative Ways to Present Your Turkey.

1. Put it on a platter. Arrange your paper bag turkey on a serving platter over a bed of parsley or tissue paper garnish. Surround the turkey with fallen leaves for a splash of vibrant color. With the right details, you’ll have a mouthwatering craft turkey worthy of a fantasy feast to show off to your friends and family.

If you don't have a real serving platter lying around, make your own out of cardboard, construction paper, and colored markers.

Make sure to let everyone, especially small children, know that your paper turkey is not for eating.

2. Add colorful designs. Before you fill the paper bags, decorate the outsides for a more artistic, funky finish. Use crayons, markers, washable paint, stickers or glitter and customize your turkey with polka dots, swirls or dazzling patterns using your favorite colors. Grab a friend, sibling, parent or child to decorate your turkey with, then compare and display them together when you’re done.

If you’re using paint or a felt-tip marker that might saturate the paper bags, allow them to dry before stuffing or shaping them.

When making paper turkeys with your kids or students, have them write down one thing they’re thankful for somewhere on the big bag.

3. Fill it with “stuffing.” For an unexpected tasty twist, ditch the newspaper and fill your turkey with popcorn, candy or other easy-to-eat finger foods instead. You can then have someone “carve” the turkey by cutting a flap in the top and have something to snack on until the main course is served. This imaginative serving style is sure to be a hit at holiday parties!

Popcorn makes a simple stuffing because it’s light and takes up a lot of space, but you could use just about any snack food, like chips, pretzels or chocolates, to fill your turkey.

Try filling the drumsticks separately with caramel corn to make “dark meat.”[6]

4. Put your paper bag turkey on display. In addition to being a fun and easy project to do with your friends or loved ones, your paper turkey will make a unique arrangement for the coffee table, arts and crafts desk or kitchen counter. It will look especially good surrounded by other festive Fall decorations. Best of all, you can store the playful papercraft away or simply make a new one the next time the holiday season rolls around.

A paper bag turkey will fit nicely with other homemade holiday decorations, such as hand turkey cutouts, popsicle stick snowflakes, and construction paper pumpkins.

Tips.

This will make a great activity for parents and teachers to do alongside their children or students.

If the paper bags you’re using have any logos, writings or markings on them, carefully turn them inside out before you begin crafting.

Line the inside of your turkey with wax or parchment paper to prevent splotchy grease stains if you plan on filling it with buttered popcorn.

Make sure you have enough of whatever food item you choose to fill the large bag.

Hot glue is preferable to other adhesives because it dries quickly and creates a strong, lasting hold.

Warnings.

Take caution when working with the hot glue and scissors. Kids should ask an adult for help with the cutting and gluing portions of the project.

Staples should be avoided, as there's no way to use them to secure the different parts of the turkey without mashing them.

Things You'll Need.

3 brown paper bags (1 large and 2 small).

1 sheet white typing paper.

A few sheets of crumpled newspaper.

Scissors.

Hot glue or craft glue.

Popcorn or other small snack foods (optional).

Various decorating supplies (optional).

Januari 27, 2020