how to make bottle penguins

How to Make Bottle Penguins.

There are lots of ways to recycle plastic soda bottles, and turning them into adorable penguins is one of them. With a little bit of paint, time, and creativity, you can turn 2 plastic soda bottles into an adorable penguin. If you have a lot of plastic soda bottles then you can create an entire penguin family!

Part 1 Assembling the Base.

1. Find 2 plastic soda bottles. The large, 2-liter (67.2-oz) bottles will work the best for this, but you can use smaller soda bottles too. Look for the kind that have the 4 bumps on the bottom. These bumps will make the feet and the hat.

The color of the bottles does not matter. You will be painting it.

2. Remove the labels and wash the bottles. Peel the labels off first, then wash the bottles inside-out with soap and warm water. Be sure to remove all sticker residue. Dry the bottles with a towel.

Wipe the bottles down with rubbing alcohol as well. This will remove any oils that might keep the paint from sticking. Let the bottles dry; this should only take a few seconds.

3. Cut the bottles in half and recycle the top sections. A craft blade will work the best for this, but you can do it with a sharp pair of scissors too. Young children should be supervised during this step.

If the cut edge is jagged, cut it smoother with a pair of scissors.

For a smaller penguin, cut the bottom 2 to 3 inches (5.1 to 7.6 cm) off of the first bottle, and cut the second bottle in half. The shorter half will make the bottom.

4. Tuck 1 bottle inside the other to make a capsule. Turn the bottles so that the cut edges are facing one another. Slide the first bottle into the second bottle by about 1⁄2 to 1 inch (1.3 to 2.5 cm). If the bottles won't fit inside one another, cut a 1⁄2 to 1 in (1.3 to 2.5 cm) slit into 1 of the bottles first; place this edge on the inside.

Make sure that the 4 bumps on the top and bottom of the capsule line up.

5. Glue the bottles together, if desired. If the bottles are loose, glue them together with tacky glue or super glue. Pull the bottles apart, and paint the inside rim of 1 bottle with glue. Slide it over the other bottle.

Hot glue is not recommended because it is too bulky.

Alternatively, you can keep the bottles loose, and use the penguin as a gift box.

Part 2 Painting the Penguin.

1. Paint the entire capsule black, then let it dry. Take the capsule outside or into a well-ventilated area. Set it down on a sheet of newspaper, then coat it with black spray paint. Let the paint dry for 15 to 20 minutes, then turn the capsule over. Spray paint the bottom and let it dry completely.

Hold the can 8 to 10 inches (20 to 25 cm) from the capsule, and spray using a side-to-side motion.

If the paint is too thin, let it dry completely, then apply another coat of paint.

If you don't have spray paint, paint the capsule using black acrylic craft paint and a paintbrush.

2. Paint the penguin's face and belly white, then allow them to dry. Use a pointed paintbrush and white acrylic craft paint to outline the white face and belly of the penguin. Fill your outline in using a flat paintbrush. Let the paint dry, then add another layer if the first layer is too thin. Let the second layer dry too, if you added it.

Look at pictures of real or cartoon penguins to get ideas for the placement of the white parts.

Make sure that 2 of the bumps on the base of the capsule line up with the bottom of the penguin's belly. These are its feet!

If you are making a smaller penguin, use the shorter half to make the bottom.

3. Give the penguin a widow's peak, if desired. Use a pointed brush and black acrylic craft paint to draw a V-shape at the top of the penguin's white face. Fill the V-shape in with black paint so that it blends in with the body. For an even nicer finish, made the sides of the V-shape curved so that it looks like Mickey Mouse's widow's peak. Let the paint dry before moving on.

4. Paint 2 eyes and a beak using acrylic craft paint. Use a yellow upside-down triangle for the beak, and 2 black dots for the eyes. For a more realistic beak, paint a yellow or orange circle, then draw a horizontal black line going through the middle.

Look at pictures of cartoon penguins to get ideas.

You can also hot glue 2 buttons or 2 googly eyes for the eyes.

If you don't have yellow paint, cut a triangle out of yellow paper, and glue that on instead.

Part 3 Adding Optional Details.

1. Give your penguin character with lashes, eyebrows, and/or blush. You don't have to do any of these, but they can really give your penguin personality. Use a very thin brush for the lashes and/or eyebrows, or a paint pen. Use a larger pointed brush to apply pink paint for the blush.

If you want to give your penguin visible yellow feet, paint the 2 bumps in the front (under the white bellow) with yellow acrylic craft paint.

2. Paint the top half of the bottle to turn it into a hat. The 4 bumps on top of your penguin's head can easily turn into a hat. Paint a line around the penguin's head, just above the eyes, then fill in everything above that line. Use whatever color you want.

If you have a molded line just below the bumps, you can use that as a guide instead.

3. Let the hat dry, then add some details. You can make the hat look more hat-like by painting or drawing some stripes or spots onto it. Use a thin, pointed paintbrush and acrylic craft paint in a contrasting color to do this. Let the paint dry when you are done.

Use a paint pen for thin stripes or small dots.

4. Glue a pompom to the top of the hat, if desired. You can make the pompom yourself out of yarn, or you can buy it from the kids section of a craft store. Hot glue the pompom to the top of the hat, right between all 4 bumps.

Choose a pompom color that matches the designs on your hat. If you did not add designs, then use a contrasting color instead.

5. Tie ribbon around the neck to make a scarf. Find some ribbon that goes well with the hat. Wrap the ribbon around the penguin's neck, then cross the left end over the right end. Bring the left end up through the gap, then tighten it. This is just like starting to tie a pair of shoes!

Glue both ends of the ribbon to the penguin so that they stay down.

If you are turning this into a gift box, make sure that you keep the ribbon below the seam.

You can also cut a long, skinny strip out of felt, and use that instead of ribbon. Cut fringes into each end for additional charm.

Question : How do we make the eyes?
Answer : Cut out two small black circles, and two slightly larger yellow circles. Glue the black circles onto the yellow circles, and glue those onto the white face.

Question : We don't have to remove the bottle cap?
Answer : If you have removed the cap, you will have to tape or otherwise plug the hole on the top to "sculpt" the rounded top of the head on, so it is not recommended to remove the cap. However, taping or a cork replacement can be used.

Question : Can I use a plastic bottle?
Answer : Yes, but it may be hard to paint.

Tips.

If you want your penguin to have a pointy hat, discard 1 of the bottom halves and keep 1 of the top halves. Use the top half as the hat.

Use paintbrushes made from sable or taklon bristles. Do not use boar bristle, horsehair, or camelhair.

Spray the penguin with varnish or sealer, if desired. Do this after you finish painting, but before you add pompoms and scarves.

You can spray the capsule with paint primer first to help the paint stick better.

If you are worried about the paint chipping, spray the capsule with paint primer before you start painting.

Warnings.

Use low-temp hot glue guns to avoid blisters and burns. Do not use high-temp hot glue guns.

Things You'll Need.

2 plastic soda bottles, Craft blade, Black spray paint, Acrylic craft paint (white, yellow, and black).

Acrylic craft paint, 2 contrasting colors, Flat and pointed paintbrushes, Ribbon or felt, Pompom, Hot glue, Tacky glue or super glue.

Januari 23, 2020

how to make a brown sock cow

How to Make a Brown Sock Cow.

Cows are a favorite barnyard animal among kids of all ages. If you want to make your own cow, there are many different ways to do it, so you can choose a craft based on the materials you have on hand.

Steps.

1. Cut the toe off. Use scissors to cut off the rounded toe end, removing roughly one-fifth of the sock in the process.

On a standard adult sock, the length of the cut portion should be between 4 and 5 inches (10 and 12.5 cm).

The cut toe portion will become the head of the cow. Save the rest of the sock for the body.

2. Stuff and seal the ends. Stuff the cut toe portion with a small bundle of fiberfill or similar filling material. Leave the top 1 inch (2.5 cm) empty; glue or sew the ends together.

Fold the raw open edge in by no more than 1/2 inch (1.25 cm).

To create a rounded head, you'll need to begin by gluing the sides of the empty portion together. Glue the opening closed, then fold it down over the stuffed bundle. Stitch or glue the folded material in place.

3. Cut off the cuff. Cut off the back opening of the sock, removing a portion equal in length to the original cut toe portion.

The cut portion should be about one-fifth the length of the original sock. On a standard adult's sock, this should be roughly 4 to 5 inches (10 to 12.5 cm).

You'll use parts of this cut portion for the ears. The leftover sock will be used for the body.

4. Separate the cuff into two ovals. Cut the cuff in half, parallel to the ribbing. Cut out one long oval from each half.

Each oval should have roughly the same width and length of the cuff half.

These ovals will become the ears. You can discard the rest of the cuff material.

5. Stitch the sides. Fold one oval in half crosswise. Using a needle and thread, blanket stitch over the the raw, rounded edge. Repeat with the second oval.

Alternatively, you can use hot glue to hold the ear halves together. Lay a thin stream of hot glue around the entire edge, then carefully press the raw edges into the glue. With the raw edges trapped, fold the oval in half crosswise, sticking both ends together.

6. Attach the ears to the head. Place the flat edge of one ear along one fold of the head. Repeat with the other ear and the other head fold.

You should be able to attach the ears with either thread or hot glue.

7. Add button eyes. Sew two buttons two the front of the head, positioning them roughly halfway between the ears and the original toe-seam of the sock.

8. Place the felt nostrils. Peel the backings off two small, self-adhesive round felt pads. Place each pad onto the original two-seam of the head.

Align these felt pads to the eyes of the cow.

9. Cut slits into the remaining sock body. Flip the remaining sock over so that the heel faces up. Cut straight slits through both sides of the material from either end of the sock.

Keep both slits as centered as possible from either end. Each should span roughly one-half to two-thirds the space in between the open end and the nearest side of the heel. On a standard adult's sock, the slits should be 2 to 3 inches (5 to 7.5 cm) long.

10. Stitch around the slits. Turn the sock inside-out and sew along all of the raw edges, leaving roughly 1 inch (2.5 cm) open along the back slit.

As you sew along the slits and the raw open edges, you should see the legs of the cow taking shape. The front of the sock should form the front legs and the back of the sock should form the back legs.

Once you finish sewing along these raw edges, turn the body right-side out again through the remaining gap.

11. Stuff the body with fiberfill. Insert fiberfill or a similar material into the body of the cow through the open gap.

When finished, carefully turn the raw edge inward. Glue or edge-stitch the opening closed.

12. Attach the head to the body. Place the head of the cow in between the heel and the front legs. Sew or glue into place.

13. Attach yarn to the back end. Cut a piece of brown yarn equal in length to the cow's back legs. Knot both ends of the yarn, then stitch or glue it in place.

The yarn become the tail of the cow. You'll need to attach one end to the back of the heel, centering it in between the two back legs. The other end should hang free.

14. Enjoy. The sock cow should now be finished.

Things You'll Need

Fiberfill stuffing,Scissors,Sewing needle,Brown thread,2 buttons,2 small self-adhesive felt pads,Brown yarn,Hot glue gun.

Desember 02, 2019

how to making a decorative pinwheel

How to Making a Decorative Pinwheel.

Pinwheels are a beautiful decoration and delight children of all ages. Use them to decorate your yard for a party, or happily watch your children as they admire the bright colors whirling together. Once you know how to make a basic pinwheel, you can make a fancier one with more spokes. You can also make a disc-shaped pinwheel. It won't spin, but it'll look lovely as a wall decoration or ornament.

1. Cut a sheet of patterned scrapbooking paper into four strips. Get some 12-inch (30.48-centimeter) square scrapbooking paper. Use a metal ruler and a craft blade to cut the paper into four, 3-inch (7.62-centimeter) wide strips.

Some scrapbooking paper has a white strip along the bottom edge for the price and label. You should trim this off first.

These pinwheels are meant to be used as decorations on gifts, walls, or ornaments. They do not spin like regular pinwheels.

2. Fan-fold the strips widthwise. Take your first strip, and fold the narrow edge over by ½ to 1-inch (1.27 to 2.54 centimeters). Use that as a fold as a guide for the rest of the paper. Repeat this step for the remaining three strips.

3. Consider adding a design to one of the long edges. Fold your strip back up so that it looks like a closed fan. Cut an angle into one of the narrow edges. Work one strip at a time, otherwise, the paper will be too thick to cut neatly.

You don't have to do this step. This will simply give the pinwheels a more ornate edge.

4. Attach the pieces together to make a longer strip. Place a strip of tape against one of the narrow ends of your first strip. Place it against the narrow end of the next strip, then press them together. Keep connecting the strips until you have one long strip.

If both ends of the strips are folded in opposite directions, they will make a V or ^ shape. Trim off one of the ends until both are folded in the same direction.

5. Attach the first and last strips together to make a disk. Run some glue or a strip of double-sided tape along one of the narrow ends. Bring the other narrow end towards it, and press the two together.

6. Flatten the disk. If the disk won't lay flat, you will need to glue a support to the back. Flip the disk over so that the back is facing you. Choose a dowel, straw, or skewer that is the same height as the disk. Hot glue your chosen stick down the center of the disk, right between two ridges.

7. How glue an embellishment to the front of the disk. For a fancy look, you can cut a small circle out of coordinating paper, then glue it to the front to cover the hole. For a more rustic touch, you can use a large button instead.

8. Cut a circle cut from cardstock to the back of the pinwheel. This will make it easier to secure the pinwheel to walls, gifts, and other items. It would be best if you use a matching color, but you can use a different color as well.

Use a cup, jar, or lid to trace the circle.

9. Use double-sided tape to secure the pinwheel. Place a few strips of double-sides tape onto the back of the pinwheel, right over the cardstock circle. Secure the pinwheel to your desired gift of banner.

If you are securing the pinwheel to a wall, consider using double-sided, foam mounting tape instead.

Alternatively, you can string several pinwheels together to make a banner.

10. Finished.


Tips.

Make your pinwheel out of thin plastic, such as acetate, binder dividers, or stencil plastic.

Wrap a pretty ribbon in a spiral around the dowel before adding the pinwheel.

For an even fancier pinwheel, paint the stick with acrylic paint or spray paint beforehand. Let it dry before adding the pinwheel.

You can use a drinking straw instead of a dowel. It won't be as durable, but it will be easier to assemble.

Glue a bead, button, or charm to the pin on the front of your pinwheel for a fancy touch.

Make your own double-sided scrapbooking paper by gluing two sheets of paper back-to-back.

Decorate plain paper with rubber stamps.

You can make a simpler pinwheel by securing everything with a thumbtack to the side of a pencil eraser.


Things You'll Need.

Colorful paper.

Pencil.

Ruler.

Scissors.

Double-sided tape.

Hot glue gun and hot glue sticks.

Stapler.

Cardboard scraps or buttons.

November 30, 2019

how to organize craft supplies

How to Organize Craft Supplies.

If you're crafty and like to make things, chances are the materials and supplies that go into your hobbies have stacked up over time, and not in a tidy way. Here's how to regain a bit of control and find what you need, when you need it.







Steps.



1. Locate all of the craft supplies that you own.

If something is basically already organized or put away, don't pull it out now. Start with the stuff that's in your way.

Go a bit at a time, especially if you have a lot of stuff. Spend fifteen minutes sorting, or just sort one bag, bin, or area.



2. Cull the excess. It can be hard to admit that a particular activity might have been a passing phase that you've outgrown, or that an unfinished project ought to remain so, but if you can reduce the amount of stuff you'll have less of it to organize and to have to cram in somewhere.

Go for the easy stuff first, to help yourself build momentum. Toss anything that's obvious: hopelessly tiny scraps, mostly empty packages, dried-up paints.

Remember, you decide what's worth keeping. At the same time, organizing only goes so far if there's too much stuff.

Be choosy about what you bring home from the craft store. Do you have a project in mind for this item? Do you have a place to put it? Do you really find it attractive or promising? Can you do the project? Anytime soon? Be realistic, and you'll save money, space, and time.



3. Sort out all of the supplies that you have into smaller groups.

Sort by item type. Put glue sticks, bottles, and jars into one pile. Put decorative stickers into a different pile. Put fancy paper into a pile of its own.

Better yet, sort by activity. Have one kit, bag, bin, or space for painting, one for paper crafts, one for yarn, knitting needles,



4. Choose where to store your supplies. Think about where and how you do crafts. If you have a craft area already, add drawers, bins, or shelves. If you knit in front of the TV, your organization may consist of a knitting basket or two with active projects that live by the sofa and a bin full of extra yarn and inactive supplies stashed away in a closet elsewhere.

Try a drawer organizer or even a fishing tackle box to corral many small items. Something with multiple smaller spaces helps separate little stuff.

If you have a lot of small items, like beads or buttons, giving each group its own small container or compartment that seals or closes tight can save spills.

Do you craft on the go? A tote bag or even a purse-sized craft kit might be just the right organization system for you. Keep a project at hand when you go out to make use of wait times.



5. Keep on sorting.

Sort a little bit whenever you start or finish a project or get new supplies.

Rearrange if you notice something isn't working. If it's not where you looked for it, put it back where you will look for it next time. If it's not handy and you use it often, put it back near the top or closer to where you work.



6. Arrange by size and shape so that things are visible and accessible. It's best if you don't have to empty an entire bin to get out one item.

Put the flat objects into the container first, standing up on one side if possible, and then place the non-flat objects on top of them or alongside. Put frequently used items near the top.

For materials, like paper or fabric, try a filing system that displays them. Stand them on edge in a bin or drawer so that you can sort through them and see at a glance what you have. Smaller pieces might be rolled and stood up in a basket or bin.



7. Repeat this process with different containers until everything is filed away.



8. Label with tape or paper what is in each container. Don't rely on sticky notes or anything else that could fall off too easily. For example, if a certain container holds glue, markers, and crayons, write that out and attach that to the container. This way, you will know what is in the container when you need to get something out of it in the future.



9. Finished.





Tips.

Buy plastic containers that are clear so that you can see through them and find supplies in them more easily.

Don't rush this process by stuffing your craft supplies into random containers to get it all over with. A small investment of time now will save time in the future.

Put things where they'll be handy when you need them, and where you think you'll look for them.

Try to get the plastic containers for a good price, but make sure they are really sturdy so you won't have to get new ones later on.

Most importantly, find your own balance between creativity and control.

Organization is whatever you want it to be. If you want your colored pencils out on display so you can grab them easily when inspiration strikes, put them in a big jar or cup wherever you like to draw.

Take the time to treat your supplies properly. Don't store brushes on their tips or leave them soaking in water. Close tightly any paints, ink, clay, and anything else that might dry out. Protect your fabric and yarn from moths and mice, but don't seal it so tightly that it becomes musty.

Don't panic if your craft area doesn't stay neatly organized. If you're using the stuff regularly, it may tend to wander around your work area and get left out. If you can, work in a back room, basement, or garage and simply close the door when people come, or deem the space your studio and let it be messy! A moderately cluttered work area could actually increase your creativity by bringing together unrelated things accidentally or by reminding you of what supplies you have available. Thus, take a casual attitude about neatening and organizing this aspect of your life. Tidy up when you feel like it, when you can't find anything, or when having the clutter around would get in your way.

Sort and organize in a way that makes the most sense to you. If you regularly use glue to affix yarn, store the glue with the yarn.



Things You'll Need.

Craft supplies.

Multiple containers depending on the amount of supplies.

Paper to label the containers.

November 21, 2019

how to make a sock monkey

How to Make a Sock Monkey.

This classic, goofy sock toy has been a favorite of children and adults for years. Making something this popular may sound like a daunting task, but it is actually quite easy. To make a sock monkey of your own, follow these steps.



Making the Legs.



Find two clean socks. The best ones will be ones with heels and toes in contrasting colors to the rest of the sock. One sock will be used to make the body, legs, and head, and the other will used to make the arms, tail, face, and ears.

These monkeys were traditionally made with “Rockford Red Heel Socks.” If you have striped socks, those work well, too. If your socks have cuffs, be sure to undo the seam carefully; the cuff length is needed for the length of the monkey.



Turn both socks inside-out.



Lay one sock with the heel flat down. You may have to flatten the sock against its natural crease to make this happen. If it's not cooperating, grab an iron and give it a quick once-over



Draw a center line on the sock from the toe to approximately one inch from the colored heel. This will become the split in the monkey’s legs. Again, note that the heel is actually hidden beneath the sock at this point, so you may have to flip it over briefly to double-check your positioning.

Erasable fabric marker works best for drawing. Make sure before you cut that your line is indeed on the halfway mark -- a monkey with one fat leg and one skinny leg is not a happy monkey.



With the sock still folded flat, sew up one side of your marked line and back down the other. Leave approximately 1/4 inch (.6 cm) between the line and each of your seams.

You can either use a sewing machine or sew by hand. If you're using a sewing machine, use your walking foot.



Cut along the line between your two seams. The monkey’s legs and colored feet will now be clearly visible.



Making the Body and Head



Turn the sock right-side out and stuff the entire thing. Polyfill stuffing is available at all craft supply stores. The upper half of the sock will become the torso and head.

The amount of stuffing is up to you. How firm do you want your monkey? If the sock is thin, you may want to err on the side of under stuffing, as overstuffing it may cause it to stretch.



Sew the head and/or hat. If your sock opening is the same color as the body of the sock, just make a nice rounded head and stitch it shut. If it is a contrasting color, you will need to decide if you want to cut it off (making a shorter body for the monkey) and make the head as usual or use the excess coloring as a "hat" by not stuffing the last inch or two and cinching the opening into a cone shape.

To make the head: Stitch around the neck with quarter inch stitches. Use sturdy thread such as embroidery floss. Pull the stitches snugly until you get the size neck you want and knot the ends. Round out the head area with stuffing as desired and stitch the top opening shut.



If you are making a hat, start working with the cuff. Gather the tip with large stitches and snug/cinch them closed. Fold the raw edges to the center and tuck inside. Then, stitch the opening closed. Winter ready!



Making the Arms, Tail, and Ears



Cut the second sock into sections as shown. Though the pattern is only drawn on the top, make sure to cut through both layers.



Fold both arm pieces in half lengthwise. Then sew up the open side in a gentle arc around the dark ends; the dark ends will become the paws and the opposites (open ends) are where the arm will be stuffed and then attached to the body.

Keep all of these sections open-ended. Make sure they're turned inside-out as you work! If they're not, all your seams will be very, very rough.



Fold the tailpiece in half lengthwise. Then sew up the open side and in a gentle arc around the dark end as you did with the arms; the dark end will become the tip of the tail and the opposite, open end is where the tail will be stuffed and attached to the body.



Fold each ear in half and cut across the crease. Then, sew in a gentle arc following the rounded sides, leaving the flat side open. The opening is where you will stuff each ear and then attach it to the body. Noticing a pattern?

If you'd like, you can then fold the ears again, forming a vertical line down the middle of the ear (giving it depth like a real ear has). Basically, pinch the edge you just sewed in and bring the two points together. Slip stitch the two sides together.



For now, do nothing with the muzzle (formerly the heel). That part's saved for later.



Flip the sewn pieces right-side out and stuff them. You should now have two arms, two ears, a tail, and an unsewn, unstuffed nose.

The tail may prove to be a bit of a problem. You could try to stuff it using regular polyfill stuffing and a pencil to poke it through, or you could use batting or part of an aquarium filter. Both the batting and the filter are a bit firmer and will create a more uniform-looking tail in the long run.



Attach the tail to the rump. Position it carefully and slip stitch it all the way around.



Attach the arms to either side of the body. You may want them a little higher than your natural inclination says; this will give your sock a more monkey-like posture.



Assembling the Face and Ears



Trim away the edges of the heel piece if necessary. Since this will form the muzzle, try to make sure the piece of fabric is uniform in color. Note that, since the outermost edges will be covered, you do not have to make them perfect.



Fold the bottom of the muzzle under and sew it to the bottom of the monkey's chin. Make sure no raw edges are visible along the bottom, but leave the top open for now.



Add stuffing to make the muzzle puff out. You may want to refer to existing images of sock monkeys as to how this should look. The best sock monkeys seem to have a muzzle that puffs out at nearly a 90º angle.



Fold the raw edge under and stitch the top edge to the face. The muzzle should take up a large amount of the area for the head -- don't worry about needing space for the rest of his features.

Go ahead, give your monkey a mouth! Along the toe line of the muzzle (which should be dead center) branch stitch in a contrasting color of thread.

If you'd like nostrils, simply embroider two small rectangles above the mouth about 1" (2.5 cm) apart.



Fold the raw edges of each ear to the inside and stitch them closed. Stitch the completed ears to the sides of the head. They should be in line with where the eyes will be, just above the muzzle. Make sure they stick out from the front!



Add button eyes. To give your monkey whites on the outside of his eyes, glue or sew the buttons onto a bit of white felt. Then, with thread of a contrasting color, sew on the felt just above the muzzle. You now have an adorable sock monkey!

For a non-demonic looking monkey, stick to black buttons. The size you need depends on the size of your monkey. And if you're giving it to a child, either avoid the buttons entirely or make sure they're sewn on really well !







Tips.

Important: when stuffing the sock monkey, use small pieces of stuffing. Using bigger pieces may be quicker, but the results aren't satisfying at all. The project will come out lumpy and, well, ugly. Smaller pieces leave a smooth finish. It may help to use the eraser end of a pencil to gently push stuffing into place.

To add personality to your monkey you can cut out a red heart and put it in your monkey's chest before you sew it up.

You can use fabric glue to add the eyes instead of sewing them on.



Further ideas.

Sew a tiny red vest for the monkey with buttons down the front to make him/her look like an organ grinder's monkey.

Embroider a mouth line on the nose or eyebrows for added expression.

Cinch elbows, knees, wrists and ankles for the monkey using the same technique as for the neck.

Add a pom pom to the hat for a winter monkey, or a flower to the hat for a spring monkey, etc.

Sew a fabric banana into the monkey's hand.

Sew a tiny red heart on the monkey's chest.

Knit a scarf for more winter fun.

If you don't have stuffing, you can use old pieces of t-shirts, crushed and dried flower petal, used dryer sheets, tissue paper, yarn, grass or rice.

If you don't have any buttons, you could use googly eyes instead.

Bright colored socks work well. Also spots and stripes are great.

Eyes can also be drawn onto your monkey. Embroidery is another option.



Warnings.

If you're giving the sock monkey to a child under three years old, don't use buttons for the eyes. If they come loose, they could end up in the child's mouth. Instead, embroider the eyes on, use child-safe doll/cat eyes, or use nontoxic fabric paint or markers to draw the eyes or use felt eyes.

Use only socks you have permission to cut up.

Scissors and needles are sharp. Be careful when using them.



Things You'll Need.

One pair of socks with contrasting colored heels and toes.

Stuffing.

Embroidery floss or yarn to match your sock.

Sewing supplies: needles, sewing machine, scissors, etc.

A bright pen/marker to copy the pattern onto the socks.

Two buttons for eyes (optional).

Extra fabric for additional details (optional).

Iron (if necessary)

November 07, 2019