how to melt glue sticks

How to Melt Glue Sticks.

Glue sticks can be melted down for a number of applications. Whether used in crafts, manufacturing, packaging, fashion, or in any other creative function, glue sticks are a cheap and easy to come by product. All-purpose or school glue sticks and hot glue gun sticks can both be melted in the microwave, and hot glue gun sticks can, of course, be melted in a glue gun. If handled carefully and done properly, the processes are extremely quick and can help you adhere all kinds of surfaces to one another.







Microwaving Glue Sticks







Remove the glue sticks from their original packaging. All-purpose or school glue sticks can be unscrewed and pulled or broken off from their plastic casings. Hot glue gun sticks simply need to be removed from any packaging or wrappers.

Make sure there are no plastics or other wrappings in or on the glue you want to melt. Most wrappings and plastics are not intended to be melted and can be unsafe to do so.

If your glue stick has a plastic piece through the center, carefully cut the glue away from the plastic using a knife.



Put the stick(s) into a microwave-safe dish. Since the glue will be very messy and hard to clean, use a single-use paper bowl. If you are dedicating the dish to the craft of melting glue sticks, a ceramic or glass mug or bowl will also work.

Be sure the glue sticks are fully inside of the dish. If they overhang the mug or bowl, they will melt outside of the dish.

Start with smaller quantities to test how long your particular glue takes to melt.



Microwave the glue on full power in 20-second intervals. Depending on your microwave and amount of glue, you should at least be able to partially melt the sticks. If there are still solids, microwave the glue for an additional 20 seconds after stirring it with a craft stick or plastic spoon.

Do not leave the microwave unattended. If something goes wrong, you should be there to stop the microwave.

Do not heat the sticks for extended periods of time. It may look like nothing is wrong while it heats, but overheating the glue can create fumes that are unsafe.



Remove the glue from the microwave carefully. You should use it immediately, but be careful as the glue will be quite hot. Depending on how long it was heated, the dish can be hot as well.

Use the glue fresh out of the microwave so it will be easy to apply.

If the glue re-hardens, simply microwave it for another 20 seconds.







Melting Glue Sticks with a Glue Gun





Obtain a glue gun at least as big as the glue sticks. Only use hot glue sticks intended for glue guns—not all-purpose or school glue sticks. If the sticks won’t fit into the glue gun, you cannot melt them. If the sticks are too small, you will just have to use your hand to feed them through.

Make sure your glue sticks are meant for a glue gun. You should not use other types of glue sticks because they can damage your glue gun.



Plug in the glue gun over cardboard or newspaper. As the tip of the gun heats, the gun may start to drip as it melts. By putting a piece of cardboard or newspaper underneath, you can protect your working surface.

Always follow the instructions specific to your glue gun regarding electricity and timing.

Do not leave a glue gun unattended. They can tip over or otherwise cause severe burns if you are not careful.



Squeeze the trigger of the glue gun to feed the sticks. If the sticks match the size of the glue gun, the trigger will allow the stick to press and feed through the heated tip. The glue will then melt and drip out wherever you point the gun.

Do not touch the metal tip of the gun or the melting glue. They will both be extremely hot.

If the glue is not feeding through, it may either be too large of a stick or may still be heating up.

If your glue stick is smaller than the glue gun, you will have to push from the back end of the stick to feed it through.

Use gloves to protect your hands from the heated materials.



Insert another stick once the first no longer feeds through. If the gun or your fingers can no longer safely feed the first stick through the rear of the glue gun, use another glue stick to press it through. It will then be caught by the plastic feeding mechanism and continue melting.





Warnings.

Do not touch melted glue. It will be extremely hot and adhere to your skin, making the burn worse.

Do not inhale melted glue fumes. Some glues are non-toxic, but not all of them are. Regardless, the fumes can be dangerous, and you may need to wear a respirator while working.

November 13, 2019

how to make a jack in the box

How to Make a Jack in the Box.

A Jack in the Box is a fun toy that's been around for hundreds of years. While it may seem complex, a Jack in the Box actually works with very simple mechanics. Making your own can be a fun arts and crafts activity. With some cardboard, glue, magnets, a spring, and a few other parts, you can make your very own Jack in the Box.







Part 1 Constructing the Box.



Find a sturdy piece of cardboard. You'll need a thick and sturdy piece of cardboard for the box to support itself. The kind from a large packing box should work well.

You'll be cutting out 6 squares that are each 6" x 6" (15 cm x 15 cm), so your piece of cardboard will need to be at least 18" x 12" (45 cm x 30). If you can't find a piece that big, then several pieces will work fine too.



Draw six 6" X 6" (15 cm x 15 cm) boxes on the piece of cardboard. These six squares will form the walls, floor, and lid of your Jack in the Box. Use a ruler to measure and make sure your lines are straight.

Make sure you use a dark pen or marker. Otherwise, you may not be able to see your lines when you cut.



Cut out each box. Use a pair of sharp scissors or a box cutter. Carefully cut along the lines you drew so the cardboard squares are the right size. If you're using a box cutter, make sure the cardboard is placed on a solid surface.

Wear gloves during this step to prevent paper cuts or any injuries for the scissors or box cutter.



Glue 4 of the squares together, making a cube with no top or bottom. Hot glue is the best choice for this step. White glue won't be strong enough to keep the box together. This forms the outside structure of the box.

Glue the edges of the cardboard together to form the cube. If the glue doesn't seem to be making a strong seal, you can use strips of tape to secure the cube while the glue hardens.



Glue another square to the bottom of the cube. Line up the square perfectly with the rest of the cube or your box will be uneven. This will form the floor of the box.

Lay the square down flat and put glue around the edge. Then slowly lower the box onto the square, making sure the glue makes contact with all edges of the box.



Make a hinge with the final square. Don't glue the final square to the box, or your Jack in the Box won't open. Instead, rest the square on top of the box, making sure to line up all the sides. Then, use a strip of tape to fasten one side of the square to the box. This will form a simple hinge that allows your box to open.

Clear tape is the best choice here. Colored tape might throw off your designs when you decorate your box later on.







Part 2 Sealing the Box.



Find 2 small magnets. There are lots of ways you could make the seal for your box, but a simple method uses magnets. Start by finding 2 magnets. These should be square or circle and small, not more than 1 inch (2.5 cm) long.

Craft or hardware stores usually have small magnets that are meant to hold boxes or cabinets closed. Looking for these should give you a good start.

Remember to find out which sides of the magnets attract each other. Those are the two sides you'll line up when making your seal.



Glue one magnet to the bottom of the box's lid. This should be on the opposite side where you placed the tape. On the edge of the lid and in the center, glue the first magnet.



Glue another magnet directly under the first magnet. The next magnet should be placed on the inside wall of the box so the two magnets touch each other when the lid is closed. In this position, they will attract each other and keep the box sealed.

To find the right position for the second magnet, start by closing the box slowly. This way you'll be able to see where the magnet will rest when the box is sealed. The best place for the second magnet is right under that point, so the two magnets touch when the lid is closed.



Test out your seal. See if your seal is holding after you glue both magnets. Pull up slightly to see how tight the seal is. Flip the box upside down and see if it holds.







Part 3 Making the Spring Puppet.



Glue a compression spring to the bottom of the box. Draw a circle in the middle of the box's floor to see where you'll place the spring. Then put glue on the bottom of the spring and place it over the circle you drew. Hold the spring down for a few seconds to make sure the glue seals.

Compression springs come in lots of sizes. For this project, you'll want one that's slightly taller than the box, or about 7 inches (18 cm). Your local craft store should have plenty of options.

Test the seal by making sure the box stays closed when the spring is in place. If the box doesn't stay closed, your spring is too big or your seal is too loose.



Put a sock puppet on the spring. Your Jack in the Box needs a character to pop out! A sock puppet is perfect because it can fit snugly over the spring.

You could also draw and cut out a simple face from a piece of paper and glue it to the top of the spring for a simpler design.



Test your box. With all the pieces in place, it's time to make sure your box is working! Put it on a table and lift up the lid. Your puppet should pop out of the box when you do this.



Decorate your box. Now that your box is complete, you can decorate it however you want! Use markers to draw on its sides, glue sparkly paper over it, cover it with stickers--use your imagination!





Tips.

Remember to let all glue dry before you move on. Wait a few minutes after you glue pieces together to make sure the glue holds or your box could warp as you work.



Things You'll Need.

Cardboard.

Hot glue.

Scissors.

Ruler.

Clear tape.

Gloves.

Pen or marker.

Compression spring.

Magnets

November 18, 2019

how to make furry cat ears

How to Make Furry Cat Ears.

Cat ears are cute accessories that can be easily made. You can wear them with a costume, or as a fun accessory with an outfit. All of the materials needed to make the cat ears can be found at most arts and crafts stores. To make furry cat ears, create the ear bases, put the ears together, and complete the cat ears with the help of an elastic band and hot glue.



Part 1 Creating the Cat Ear Base.

1. Draw the cat ears on paper. This will be the template for the wire. Basically, you just need to draw two wide triangles. You might like to try drawing a few different sizes to see which size looks best on your head. You can cut out the template, or leave the cat ears drawn on the paper. Keep this design as your template for the remaining steps.

Keep in mind that the template will be slightly smaller than the finished ears because of the fur. A template of about three inches is a good size to use.

It doesn’t matter what you use to draw the ears, but pencil is good to use if you will be redrawing the ears multiple times.

2. Create the cat ears with jewelry wire. Following the paper template, bend the wire into the shape of the cat ears. Jewelry wire should be fairly easy to bend, but you can use a pair of long nose pliers to help form the shape. Do this for both ears and you should end up with two triangle shaped ears.

If you don't have wire, you can use paperclips. Just straighten them out and use them as wire. Don't worry if they don't make a perfect triangle. It won't matter when you put them in the fur. Use glue to bind the sides until you put them in.

Use a jewelry wire that is thicker so that it won’t fall out of shape when fur is added to them. 16 or 18 gauge is a good choice because it is thick, but can be bent without too much effort by using pliers.

3. Cut out the fake fur. Following the paper templates again, cut out four triangle shapes in fur. You can use any type of fur that appeals to you, like black, leopard print, or lion-like fur. Fur can be purchased at an arts and crafts store. These should be about a half an inch larger than the template, though, as the fur needs to hold the wire triangles inside once stitched up.

Remember that you can always make it smaller if it's too big, but you can't make it bigger if it's too small.



Part 2 Putting Together the Ears.

1. Sew the fur together. Place two fur pieces together. The fur sides should be facing each other. Sew each side, but leave the bottom edge unsewn. That is the part you are going to insert the wire through to shape the ears. The finished product should be inside out. Repeat this step until you have two ears.

There should be very little seam allowance—only about an ¼ of a inch.

Use a color of thread that best matches the color of fur.

2. Flip the ears so that you can see the fur. The ears should be inside out with the fur parts facing each other once you have finished sewing. Now, turn the ears so that the fur is on the outside. The ear shape should be really obvious now. Inspect the ears to make sure that there aren’t any holes or mistakes.

Turn the ears inside out and sew up any holes that you find.

Use a pair of sewing scissors to cut the thread where any mistakes have been made. Remove the thread from that part and sew it back up with new thread.

3. Place the wire triangle pieces inside each ear. Insert the wire you shaped into triangles earlier into the furry ears. The wire should be able to fit snugly inside of the fur without too much or too little room. Adjust the wire if necessary.

4. Sew up the bottom of the ears. Once you have inserted the wires into the furry ears, sew up the bottom portion that is still open. There shouldn’t be any opening on the ears when you have finished sewing. It doesn't matter if this sewing line is messy, as nobody is going to see it.



Part 3 Completing the Furry Cat Ears.

1. Create the band for the ears. Measure the elastic band or ribbon around your head. The ribbon should cross over the top of your head rather than your forehead. You can find a band or ribbon at most arts and crafts stores. Sew or hot glue the ends together to form a circular headband that fits your head. If you’re using a ribbon, you can also choose to tie the ribbon in the back so that it is adjustable.

If sewing, include a seam allowance in your measurements before cutting the ribbon. Tie the ribbon when testing it on your head to see how much ribbon will be needed in total.

You can also choose to use a headband instead of an elastic band or ribbon.

2. Mark the placement for the ears. First, hold the band and ears together to see where the ears look most natural. Then, check in the mirror to see where the ears look best. Making marks on the headband while it is on your head, use a pen or marker to make marks where the ears will be covering.

It may be easier to have someone help you make the marks while the band is on your head.

3. Attach the ears to the headband. Use hot glue to attach the cat ears onto the headband in the positions that you marked. Use just enough so that the ears stay up, but don’t use so much that the glue gets on other places on the headband or ribbon. Allow at least ten minutes for the glue to dry.

Have someone help you with the hot glue if you aren’t comfortable with using it on your own.

4. Check the finished product. Once the glue has dried, try on the ears. The band should fit your head without sliding. The ears should be standing straight up. Make any adjustments as needed.



Question : What if I don't have any wire, or my parents won't let me use any?

 Answer : Depending on the size of your cat ears and the thickness of the fur, you might not even need any wire to make them stand up; the wire is there for support. If the ears still flop over after you have made them, try filling them with some cardboard or craft foam instead.

 Question : Is there any alternative to the fur if I don't have a lot of money and can't buy felt or fur and don't have a cat?

 Answer : If you own any old stuffed animals that you don't care for anymore, you can use the fluff from those.

 Question : Can I use white fur?

Answer : Absolutely.

Question : What do I do if I don't know how to sew?

Answer : You can always ask a friend or family member. If you're feeling ambitious, you can learn how to sew yourself.

Question : Can I use real cat hair?

 Answer : Yes, if you want, but it may be best to pick the cat's fur off of the cat brush, not the cat itself.

Question : How can I make fake fur?

 Answer : You can make the fur by tearing felt to make fluffy strips. Then, get the same color felt, and glue or sew the fluffy stripes onto it and then cut out the triangle shape for the ears.

Question : How can I make wolf ears the same way?

 Answer : Make the shape a bit taller and more pointy. Look at pictures of wolves for reference on how their ears are shaped and then just change the shape.

Question : Could I put pink felt in the center for the finished ear?

 Answer : Yes. Just sew or glue it on with a color similar to the color of the felt.

Question : Where can I get fake fur?

 Answer : A craft store or someplace that sells fabric. Or you could remove some from a stuffed animal.

Question : Can I make non-fluffy ears?

 Answer : Yes, but you may need to expand on your ideas, especially if you are looking to cosplay with them. You could use polymer clay.



Tips.

Fake or fun fur makes a mess when cut. Have something ready to sweep or vacuum it up.

Warnings.

Use care when handling hot glue, as it can easily burn.

Things You'll Need.

Paper for template.

Scissors.

Thin wire for the ears.

Fake fur (20 cm sq. or 7.9 inches.).

Elastic ribbon (5-6 cm or about 1 or 2 inches wide) Make sure you have enough to fit around your head and extra ribbon left for tying.

Hot glue.

Needle.

Thread.

Paper.

Marking tool.

Scissors.

Februari 12, 2020

how to making a craft penguin for children

How to Making a Craft Penguin for Children.

Whether as a crafts project for a small child or as an origami project for older people, there are plenty of ways to make a paper penguin that are fun for people of any age!

Steps.

1. Get one white, one black, and one orange sheet of construction paper. Since origami can be a bit difficult (and not very exciting) for younger children, the good old method of cutting and gluing construction paper might be more up their alley. This method of making a paper penguin calls for one white, one black, and one orange sheet of construction paper.

2. Trace an oval shape onto the black construction paper. To form the body of the penguin, have the child draw an oblong oval on the black construction paper with either a white crayon or a piece of chalk so that they can see the outline. One fun and silly way to help the child make the shape is to have him or her place their shoe on the sheet and trace the outline of it.

3. Cut out the black oval. Using a pair of scissors (safety scissors for younger children), have the child cut out the black oval from the construction paper. When it comes to the eyes later, you can have the child either draw them on the white paper or cut pupils out of the black paper. For the latter, you can have the child cut those out now as well.

4. Trace a smaller oval onto the white construction paper. You can now have the child trace the white portion of the belly on the white construction paper. You can find something of the relative oblong shape to let the child trace it again or simply allow them to do it freehand.

5. Glue the belly to the rest of the body. Once the child is done tracing the white oval, allow them to cut the shape out of the construction paper. Then use a glue stick to glue the tummy portion to the rest of the body. Glue it closer to the bottom of the body portion than the middle since the head should be above it.

6. Cut a small triangle out of the orange construction paper. To make the beak for the penguin, have the child cut a small triangle out of the orange construction paper. The beak doesn't have to be an exact triangle, so you can have the child trace it first or simply cut one out.

For very small children, the size of the beak might be too difficult for them to cut out, so you may have to help with this step.

7. Glue the beak to the penguin's face. You have two different options to glue the beak to the penguin's face. You can either glue the triangle flat with one of the points facing downward, or you can actually make a little fold on one of the flat sides and glue it at the tab, which will make the beak stick out from the penguin's face.

8. Make the penguin's eyes. As mentioned earlier, you can have the child draw eyes on the white construction paper, cut them out and glue those to the penguin, or you can also have the child cut the whites of the eyes from the white construction paper, then use the black construction paper to cut out the pupils.

A third option if the child is too young to cut out such small circles is to have some googly eyes on hand from a craft store or the craft section of a big-box store. Young kids may have an easier time using a glue stick to attach google eyes instead.

9. Let the child customize it. This makes an easy basic shape for the penguin, and then the child can have fun customizing it. If the child cuts out two really flattened ovals from the black paper, he or she can glue them to the side of the body as wings. If the child wants to make feet for the penguin, you can have them trace a leaf or something else with the slight contours to give them the webbed shape.

Things You'll Need.

Scissors.

One white, one black, and one orange sheet of construction paper.

Glue stick.

Googly eyes.

Crayons.

Desember 22, 2019

how to make seashell fish easy craft

how to make seashell fish easy craft

You’re home from the beach with a collection of shells.  And now you need something to do with all of them! While we have these adorable seashell creatures on the blog, the kids will love making this school of seashell fish too! They’d look great in a shadowbox frame on your child’s bedroom wall.



Fish made out of sea shells.



SEASHELL FISH.

No trip to the beach this summer? Doesn’t matter! Seashells are readily available at craft stores, but you can also find them at garage sales, thrift stores, and even flea markets. Often times they are sold in big bags, which is how I found most of mine. I always look for them when I’m out at garage sales though!



We love seashell crafts, we even have one for adults, pretty seashell wine charms! They make great party favors or to have just because.





Seashell Fish with googly eyes.



WHAT YOU NEED TO MAKE SEASHELL FISH.

Assorted seashells.

Googly eyes, various sizes.

Hot glue gun or instant grab.



To make these fish, you’ll need seashells in assorted sizes; big ones for the bodies and smaller ones for the fins. You’ll also need googly eyes and some hot glue. You can also use instant grab glue if you prefer not to use a hot glue gun with the kids.



White craft glue is a little harder because it takes longer to dry and the shells may not stay put, so look for a fast drying type.







Lay the shells out first, deciding how you want your fish to look.



Then simply glue them together and add your googly eyes!

November 03, 2019

how to keep glitter from falling off

How to Keep Glitter from Falling Off.

If you’re a glitter lover, chances are you’ve run across crafts and body glitters that are susceptible to flaking off and leaving a glitzy, sparkly trail behind you. Luckily, there are a few different ways you can craft with and wear glitter so that it doesn’t fall off so easily. Try using Mod Podge to seal in the glitter in your crafting projects, or mix cosmetic-grade glitter with different beauty products to create your own body glitter.







Using Mod Podge for Crafts.



Add a layer of satin or gloss Mod Podge to your craft. Use a foam brush or paintbrush, depending on your craft, and lightly brush a thorough layer of Mod Podge onto the surface area of whatever you are looking to cover in glitter. Make sure the entire area is coated and that there are no bare spots.

You can even make your own Mod Podge at home to save money!

If you don’t have Mod Podge, you could also use regular white school glue, though school glue often chips off easily over time.

Fun ideas of things you can add glitter to: plates, mugs, containers, candles, fabric flowers, glasses frames, cell phone covers, wood, and notebooks or folders.



Dust, pour, or poof the glitter over the Mod Podged area. Depending on the kind of glitter you are using, you might apply it in a slightly different way. The main thing to remember is that you want to completely coat the Mod Podge in glitter and not leave any empty spaces.

You can also use a foam brush to spread on your glitter if you want a little more control over how much you use.

If you are looking for a high-glitter outcome, you can apply a second layer of Mod Podge and glitter immediately after the first one without waiting for it to dry first (it will take a little longer to dry after the second coat, then, but it will be highly glitterized).



Allow the glitter and Mod Podge to dry for 1-2 hours. Leave your newly glittered item alone for several hours or until it is dry to the touch. Try to leave it in a position so that the Mod Podge and glitter isn’t touching any other surface.

If you are adding glitter to multiple items, this is a great time to continue working on those projects while you’re waiting for others to dry.



Apply a top layer of Mod Podge to seal in the glitter. Once the first layer is dry to the touch, use your sponge or paint brush to add another thin layer of Mod Podge to your item. Use long, even strokes to reduce the appearance of brush lines. Make sure you cover the entire item and don’t leave any raw glitter poking through.

You could also use watered down school glue to create an opaque sealant for your crafting project.

The top layer of Mod Podge acts as a sealant and will prevent the glitter from flaking away.





Let your finished craft dry for 3-4 hours before you use it. Depending on how thickly you applied the Mod Podge, you may need to wait anywhere from 3-12 hours before you can safely use the item without potentially messing up the application. Always check the directions on the bottle for tips and guidelines.

If you have a dehumidifier, you can set your craft in front of it for a speedier drying time.

Never place your item directly in front of a heat source, like an electric heater or a hair dryer, as this may cause the Mod Podge to melt or change consistency so it doesn’t dry correctly.



Coat flaking items with sparkle Mod Podge to seal in the glitter. If you have an item that has glitter that is flaking off, you can apply pre-glitterized Mod Podge to add back some sparkle and lock in the remaining glitter. Simply use a sponge or paint brush to apply a thin, even coat of the sealant to the item, then let it fully dry before you use it again.

Make sure to work on a protected surface, like a counter covered in newspaper or paper towels.



Mix Mod Podge with your glitter of choice for a stronger glitter look. Pour some Mod Podge into a disposable cup or bowl and mix in as much glitter as you want to make your own glitter sealant. You can make the glitter as weak or as strong as you prefer. Then follow the instructions to apply the Mod Podge and let it dry.

You can also apply your glitter Mod Podge, another layer of glitter, and then top it off with the glitter Mod Podge again for even more glitter fun.









Wearing Body Glitter.



Combine body oil and loose glitter for an all-body glitter-wearing option. Instead of sprinkling loose body glitter on your arms and hoping it doesn’t fall off, combine body oil and loose glitter in a travel-sized shampoo container. Shake the container up really well, and then apply it to your arms, legs, chest, or face whenever you need an extra glitter boost.

While you could purchase body oils or lotions that already have glitter in them, it can be less expensive and more fun to do it yourself.



Put petroleum jelly on your skin and add body glitter for a sparkly look. Use a clean makeup or paint brush and apply an even layer of the petroleum jelly to the area you want to cover in glitter (like your collar bones, shoulders, or even your hairline). Then use another clean brush or your hand to gently press loose body glitter onto the jelly.

Visit a cosmetics store to buy body-specific glitter, which is usually a slightly different consistency than the glitter used for crafting.

If you don’t have petroleum jelly, you could also use hair gel as the sticky base for your body glitter.

Use this method in areas that aren’t going to come into frequent contact with other surfaces. For example, it probably wouldn’t work well on your legs if you are going to be sitting and standing and walking around often.



Mix hairspray and glitter to create glitter brow and hair gel. Spray hairspray into a dish, like a small cup or bowl (or even a disposable Dixie Cup), and add loose glitter. Mix it around with a toothpick or a spoolie brush, and then apply it carefully to your eyebrows or to select strands of your hair.

Do not use the glitter and hairspray mix on your eyelashes as it could irritate or infect them.



Wear vibrant lipstick and then add loose glitter for a shimmery lip look. Steer clear of sticky or glossy lipsticks and stick with a cream base to keep the glitter in place better. Put on a layer or two or lipstick, then use your fingers to gently press loose glitter into your lips.

With this trend, you’ll want to avoid pressing your lips together or eating or drinking anything too messy.



Create a glitter stamp from a makeup sponge and loose glitter. Cut a makeup sponge into a fun shape (like a heart or a star) and dip one side of it carefully into loose glitter. Spread a thin layer of petroleum jelly or hair gel on your body where you want the stamp, and then press the makeup sponge onto the jelly to transfer the glitter.

Your glitter stamp should stay on all day as long as it doesn’t brush up roughly against anything else.







Keeping Glitter on Clothes.



Use hairspray for a quick fix on your glitter clothing. Take your item of clothing outdoors or to a well ventilated area, and lay it down completely flat. Then spray a light coat of hairspray overtop of the glitter. Use unscented hairspray if you can. Allow the hairspray to dry completely before you wear the clothing item.

Hairspray is a great, quick fix, but overtime it doesn’t hold up, though you can reapply hairspray when you need to. Long-term, you just have to care for and store glittery clothes very carefully.



Affix glitter to your clothes with fabric glue. Lay out your item of clothing in a clean workspace, and apply the fabric glue in whatever patten you want. Then, carefully shake loose glitter overtop of the glue, coating it so that none of the glue is visible. Let the glue and glitter dry for several hours before picking up the item and shaking off the excess glitter.

You could even make a stamp out of a sponge and decorate your shirt that way (like stars all over a t-shirt), and then shake the glitter on top of the design.



Wash glittery clothes sparingly and let them air-dry. When you go to clean your clothes that have glitter on them, try to wash then only when they really need it. Use cold water and the delicate cycle in the washing machine, and don’t put them into the dryer. Instead, hang them up to air-dry.

You could even take your glittery clothes to a dry cleaner instead of washing them yourself.



When crafting with glitter, try working over a cooking tray. You’ll catch all the excess glitter that falls off and can easily return it to its container.

When making your own body glitter, try to use cosmetic grade glitter rather than crafting glitter.

Store your glittery clothes in plastic bags to protect them from rubbing up against other items in your closet (and to protect your other clothes from getting glitter all over them).





Things You’ll Need.

Crafting with Glitter and Mod Podge.

Mod Podge (satin, gloss, or glitter).

Foam brush or paintbrush.

Disposable cup or bowl.

Craft glitter.

Wearing Body Glitter.

Makeup or paint brush.

Petroleum jelly.

Hairspray.

Lipstick.

Makeup sponge.

Body oil.

Cup or bowl.

Cosmetic grade body glitter.

Keeping Glitter on Clothes.

Hairspray.

Fabric glue.

Plastic baggies.

November 08, 2019

how to make plastic spoon monsters

HOW TO MAKE PLASTIC SPOON MONSTERS.

Monsters and Halloween go hand in hand. They don’t always have to be scary though, like my monster bookmarks, which are pretty darn cute! All these plastic spoon monsters want to do is go trick or treating! So what do you say? Want to make some cute monsters of your very own?



MAKE FUN PLASTIC SPOON MONSTERS.

This easy craft for kids has Halloween written all over it… seriously. Did you see the trick or treat bags?? The kids can make these plastic spoon monsters and display them in a diorama, just poke the handles into some foam!



They can also double as puppets so kids can put on a Halloween puppet show. Either way, it’s a fun afternoon of make-believe!



You can decorate their faces however you like, though I am partial to the cyclops look. One eye, one eyebrow, and usually one fang!



I also think monsters with multiple eyes are super cute! I like making their eyes go in different directions.



Seriously, if one of these cute little guys walked up to you, you would totally take them trick or treating, right??



Ok, enough chatter. Let’s get on with it. Gather your supplies and get ready to make these cute plastic spoon monsters!



I made five plastic spoon monsters, but the instructions below are for just one. I chose five different colors and matched them all up. You can mix and match and do whatever you want! For paint, I used Americana in Bright Orange, Sour Apple, Bright Yellow, Lavender, and Red Alert.



SUPPLIES FOR ONE PLASTIC SPOON MONSTER.

Felt in color of your choice, cut into a 4″ x 3″ rectangle.

Pipe cleaner (same color as felt).

Plastic spoon.

Acrylic craft paint in black, white and color to match your felt.

Paintbrush.

Scissors.

Round sponge applicators (spouncers).

Hot glue gun.

For trick or treat bag.



1/3 gold pipe cleaner.

Paper bag cut into 2″ x 1.5″ rectangle.

Fine point black marker.



Paint the back of the spoon and halfway down the handle. Allow to dry and repeat for a second coat.



Use spouncers dipped in white and black paint to add eyes. Allow to dry completely.



I like the double-ended spouncers. There are two different sizes in one. Check your local craft store to see what they have.



Use the handle end of a paintbrush to add circles that are smaller than your spouncers.



Meanwhile, while the paint is drying, fold the felt rectangle in half lengthwise and cut a small slit 1/2-inch from the top.



Unfold felt and trim off excess above the slit. Be careful not to cut it too close.



Cut around the edges of the felt to create fun shapes for the monster costumes.



When the paint is completely dry, insert the handle of the spoon into the slit of the felt so that the handle ends up behind the felt. Use a dab of hot glue to secure the felt to the “neck” of the spoon monster.



For the next step, you will need to lift the felt and move it out of your way which is why the painted faces should be completely dry before you do this!



For the arms, fold a pipe cleaner in half and twist around the middle of the spoon handle. Stretch pipe cleaner arms to the left/right. Bring the felt back down and secure it to the spoon handle with hot glue.



Write “TRICK OR TREAT!” on the paper bag rectangle. Bend the gold piece of pipe cleaner in half and curve the bend to look like a bag handle. Hot glue the handle to the back of the treat bag.



Twist the end of one of the arms around the treat bag handle. Position the arms however you like!



I hope you had fun making these cute little monsters from plastic spoons! I have some other crafts you will probably enjoy like these plastic spoon bugs and these plastic spoon snowmen! And I told you I love to make monsters.

November 03, 2019

how to organize craft supplies

How to Organize Craft Supplies.

If you're crafty and like to make things, chances are the materials and supplies that go into your hobbies have stacked up over time, and not in a tidy way. Here's how to regain a bit of control and find what you need, when you need it.







Steps.



1. Locate all of the craft supplies that you own.

If something is basically already organized or put away, don't pull it out now. Start with the stuff that's in your way.

Go a bit at a time, especially if you have a lot of stuff. Spend fifteen minutes sorting, or just sort one bag, bin, or area.



2. Cull the excess. It can be hard to admit that a particular activity might have been a passing phase that you've outgrown, or that an unfinished project ought to remain so, but if you can reduce the amount of stuff you'll have less of it to organize and to have to cram in somewhere.

Go for the easy stuff first, to help yourself build momentum. Toss anything that's obvious: hopelessly tiny scraps, mostly empty packages, dried-up paints.

Remember, you decide what's worth keeping. At the same time, organizing only goes so far if there's too much stuff.

Be choosy about what you bring home from the craft store. Do you have a project in mind for this item? Do you have a place to put it? Do you really find it attractive or promising? Can you do the project? Anytime soon? Be realistic, and you'll save money, space, and time.



3. Sort out all of the supplies that you have into smaller groups.

Sort by item type. Put glue sticks, bottles, and jars into one pile. Put decorative stickers into a different pile. Put fancy paper into a pile of its own.

Better yet, sort by activity. Have one kit, bag, bin, or space for painting, one for paper crafts, one for yarn, knitting needles,



4. Choose where to store your supplies. Think about where and how you do crafts. If you have a craft area already, add drawers, bins, or shelves. If you knit in front of the TV, your organization may consist of a knitting basket or two with active projects that live by the sofa and a bin full of extra yarn and inactive supplies stashed away in a closet elsewhere.

Try a drawer organizer or even a fishing tackle box to corral many small items. Something with multiple smaller spaces helps separate little stuff.

If you have a lot of small items, like beads or buttons, giving each group its own small container or compartment that seals or closes tight can save spills.

Do you craft on the go? A tote bag or even a purse-sized craft kit might be just the right organization system for you. Keep a project at hand when you go out to make use of wait times.



5. Keep on sorting.

Sort a little bit whenever you start or finish a project or get new supplies.

Rearrange if you notice something isn't working. If it's not where you looked for it, put it back where you will look for it next time. If it's not handy and you use it often, put it back near the top or closer to where you work.



6. Arrange by size and shape so that things are visible and accessible. It's best if you don't have to empty an entire bin to get out one item.

Put the flat objects into the container first, standing up on one side if possible, and then place the non-flat objects on top of them or alongside. Put frequently used items near the top.

For materials, like paper or fabric, try a filing system that displays them. Stand them on edge in a bin or drawer so that you can sort through them and see at a glance what you have. Smaller pieces might be rolled and stood up in a basket or bin.



7. Repeat this process with different containers until everything is filed away.



8. Label with tape or paper what is in each container. Don't rely on sticky notes or anything else that could fall off too easily. For example, if a certain container holds glue, markers, and crayons, write that out and attach that to the container. This way, you will know what is in the container when you need to get something out of it in the future.



9. Finished.





Tips.

Buy plastic containers that are clear so that you can see through them and find supplies in them more easily.

Don't rush this process by stuffing your craft supplies into random containers to get it all over with. A small investment of time now will save time in the future.

Put things where they'll be handy when you need them, and where you think you'll look for them.

Try to get the plastic containers for a good price, but make sure they are really sturdy so you won't have to get new ones later on.

Most importantly, find your own balance between creativity and control.

Organization is whatever you want it to be. If you want your colored pencils out on display so you can grab them easily when inspiration strikes, put them in a big jar or cup wherever you like to draw.

Take the time to treat your supplies properly. Don't store brushes on their tips or leave them soaking in water. Close tightly any paints, ink, clay, and anything else that might dry out. Protect your fabric and yarn from moths and mice, but don't seal it so tightly that it becomes musty.

Don't panic if your craft area doesn't stay neatly organized. If you're using the stuff regularly, it may tend to wander around your work area and get left out. If you can, work in a back room, basement, or garage and simply close the door when people come, or deem the space your studio and let it be messy! A moderately cluttered work area could actually increase your creativity by bringing together unrelated things accidentally or by reminding you of what supplies you have available. Thus, take a casual attitude about neatening and organizing this aspect of your life. Tidy up when you feel like it, when you can't find anything, or when having the clutter around would get in your way.

Sort and organize in a way that makes the most sense to you. If you regularly use glue to affix yarn, store the glue with the yarn.



Things You'll Need.

Craft supplies.

Multiple containers depending on the amount of supplies.

Paper to label the containers.

November 21, 2019

how to paint wood crafts

How to Paint Wood Crafts.

Many arts and craft stores sell blank wooden pieces that you can paint. While you can always paint them right away, there are a few steps that you can take to ensure a neater, longer-lasting finish. Sanding the piece first will get rid of any ridges, while priming it will help the paint stick on better. Adding a coat of sealer will protect all your hard work, and help it last for years to come.





Prepping the Wood.



Sand the surface of the object with 140 to 180-grit sandpaper. You can do this with a sanding sponge or with a piece of sandpaper; a sanding sponge will work the best on curved surfaces, however. Also, make sure that you are sanding with the grain of the wood, not across it.

Some wooden pieces from craft stores come pre-sanded. If the surface area is completely smooth, skip this step.



Wipe the dust away with a tack cloth. A tack cloth is a special, sticky cloth intended for this purpose. You may find it alongside the sandpaper in the craft store or in the hardware store. If you can't find a tack cloth anywhere, try a damp cloth instead.

It would be a good idea to do this, even if you didn't sand your piece; items bought from stores are sometimes dusty, which can prevent the primer and paint from sticking.



Apply a coat of primer. You can use the brush-on kind or the spray-on kind. This will seal the wood surface, and help it take the paint better. It will also help the paint show up better, especially if you are using a light color.

Prime the front and sides first, let them dry, then prime the back.

Image titled Paint Wood Crafts Step 4



Allow the primer to dry before moving on. For an even smoother finish, you can sand the first coat of primer, wipe it clean, then apply more primer over it. Do this a few more times until there no ridges remain.







Painting and Sealing the Wood.



Pour a dollop of acrylic paint onto a palette. Choose a color for the background, then pour out a small amount onto a palette. Acrylic paint dries quickly, so don't pour out your other colors just yet. You can use the cheap, craft-grade acrylic paint that comes in bottles, or you can use the more-expensive artist's grade that comes in tubes. If you are using the artist's grade, dilute it with a few drops of water until it has the consistency of cream first.

You can use small dishes, plastic lids, and paper plates as palettes.



Apply a coat of paint over your piece. Use a foam brush or a wide, flat paintbrush to apply the paint. Let the paint dry, then apply a second coat, if needed. Let this second coat dry as well. Do the front and sides first, let them dry to the touch, then do the back.

Look for brushes made from taklon, katakana, or sable. Avoid camel hair brushes or stiff, bristle brushes.

Don't overload the brush with paint. The paint should come no more than halfway up the bristles.



Let the paint dry, then add a second coat, if needed. How long this takes depends on the brand that you are using. Most types of acrylic paint will dry in about 20 minutes, however. If the paint is too thin, add another coat of paint, and let it dry as well.

Take this time to clean your brush(s) with water. Do not let the paint dry on the brushes.



Add your designs and details. You can use stencils or trace designs onto the wooden piece. You can also free-hand the designs as well. Apply the base color first, let it dry, then add the details. For example, if you wanted to paint a smiley face, you'd paint the yellow circle first, let it dry, then add the smile and eyes.

Dip the brush in water often to keep the paint wet, even if you are using one color.

If you are working with multiple colors, keep a cup of water nearby. Rinse the brush with water before switching to a new color.



Let the paint dry completely. Refer to the label on you tube of paint for exact drying times. Just because something feels dry to the touch does not mean that it is ready to handle or take on sealer. Every brand will be different, but you can expect this to take about 24 hours.



Apply 1 to 2 coats of sealer. Sealers come in many different finishes, including matte, glossy, and satin; choose one that you like the best. Apply a thin coat of spray-on or brush-on sealer, then let it dry. Apply a second coat, if needed, and let that one dry too.

If you are using the brush-on kind, apply it using a wide, foam brush.

If you are using a spray-on varnish, be sure to work in a well-ventilated area.







Trying Other Techniques.



Skip the priming if you want to paint a design over bare wood. Instead, consider painting over the entire piece using a wood stain or a sealer. Wait for the stain or sealer to dry, then paint your designs onto the wood. Be sure to seal everything after the paint dries.



Add designs using stencils. Buy or make a stencil, then place it over the wood. Paint over the stencil using decoupage glue; this will seal the wood and prevent the paint from leaking under the stencil. Let the decoupage dry, then paint over the stencil. Peel the stencil away while the paint is still damp. Seal the wood using a spray-on or brush-on sealer.

You can make stencils using contact paper or self-adhesive vinyl.

You can use this method over bare, unsealed wood.



Use graphite paper to trace designs, then fill them in. Place a sheet of graphite paper over your piece of wood, graphite-side-down. Draw your design, then lift the paper away. Go over the outline using a thin, painted brush, then fill the design in using a flat brush. This method works best over painted wood. You can do it over bare wood, but the paint may not stick as well.

If you don't know how to draw, print the design out on tracing paper first, then place the tracing paper on top of the graphite paper.

If you are working over a dark-colored surface, make some chalk graphite paper instead: cover the back of a piece of paper with chalk, place it chalk-side-down onto the wood, then trace your design.



Create a tinted stain to show off the wood grain. Apply a thin layer of acrylic paint using a dry paintbrush. Dip a wet cloth in a small amount of paint, then rub it over the wood. This will help blend strokes together without covering up the wood grain.

The cloth should be wet, but not dripping.

Alternatively, you can paint over the entire piece using watered down acrylics or watercolor paints.



Make a DIY chalkboard. Paint the surface of the wood with 2 to 3 coats of chalkboard paint. Let the paint dry, then paint designs using normal paint onto it, if desired. Allow the chalkboard paint dry and cure completely. Cover the board with chalk, then wipe the chalk off.

Keep the designs on the edges of the wooden piece so that you can use the surface as a chalkboard.

You do not need to prime a DIY chalkboard, but sanding it would not be a bad idea.





Tips.

You can spray paint the wood first, then paint more intricate designs using acrylic paint.

Remember to prime, paint, and seal the bottom of your piece as well!

It is better to apply several thin coats of paint, primer, and sealer rather than one or two thick coats.

You get what you pay for when it comes to brushes. For the smoothest finish, consider investing in a high-quality brush.

Let the paint and sealer cure for 3 weeks before handling the piece. If you must handle the piece sooner, do so gently and with great care.

Choose your paint colors carefully. Acrylic paint typically dries 1 to 2 shades darker.

Use small, round, pointy brushes for precision and details, and wide, flat brushes for curves and backgrounds.

You don't absolutely have to prime the wood, but it is highly recommended. You can skip this step for a simple, kid's craft project, however.



Warnings.

Wear a dust mask over your face while sanding the wood for added protection.

Always using spray paint or spray-able primers/sealers outside or in a well-ventilated area.



Things You'll.

Wooden object (ie: frame, box, letter, toy car, etc).

140 to 180-grit sandpaper

Primer.

Acrylic paint.

Paintbrushes.

Sealer.

November 10, 2019